JVC CA-MXK50R Скачать руководство пользователя страница 13

Страница: 13 / 70

1-13

MX-K50R

Prior to performing the following procedure, remove
the CD tray.

Detach the belt from the pulley on the upper side of
the CD changer unit (Do not stain the belt with
grease).

Disconnect the card wire from the pickup unit
connector on the under side of the CD changer unit.

Attention : Solder is put up before the card wire is
removed from the pick-up unit
connector on the CD mechanism
assembly.
(When the card wire is removed without
putting up solder, the CD pick-up unit
assembly might destroy.)

Disconnect the motor wire harness from connector
on the CD board.

Remove the screw C attaching the switch board and
release the two tabs e attaching the switch board
outward and detach the switch board.

Remove the two screws D attaching the CD board.
First release the two tabs f and two tabs g attaching
the motor, then release the CD board.

If the tabs f and g are hard to release, it is
recommendable to unsolder the two soldered parts
on the motor terminal of the CD board.

Removing the belt, the CD board and the
switch board (See Fig.8 and 9)

Soldering

Card wire

Picup unit
connector

Fig.9

Fig.8

Belt

CD changer unit

CD board

Tabs g

Tabs f

Soldered parts

Motor

Switch board

CW3

Tabs e

CD mechanism board

motor connecter

Pickup unit connector

Содержание CA-MXK50R







































































Результаты поиска

Содержание CA-MXK50R

Отзывы:

Бренды по названию

Популярные бренды

JVC CA-MXK50R, Руководство по обслуживанию

Результаты поиска

Содержание CA-MXK50R

Отзывы:

Бренды по названию

Популярные бренды