1
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking information is for use by your
KENWOOD dealer, an authorized KENWOOD service center, or the
factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the
packing material. If any items are missing or have been damaged
during shipment, file a claim with the carrier immediately.
Item
Part Number
Quantity
Front glass
B10-2781-XX
1
Dressed screw
N08-0563-XX
1
Bracket
J29-0725-XX
2
Flat head machine screw
N32-4008-XX
4
Handle
K01-0421-XX
1
DC cord
E30-3427-XX
1
Lead wire with connector (15 pin)
E31-3228-XX
1
Fuse (15 A)
F52-0042-XX
1
SYNC cable
E3A-0177-XX
1
Instruction manual
B5A-0714-XX
1
INSTALLATION
To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.
Consult your dealer for installing the repeater and antenna.
MICROPHONE
Connect an optional KMC-30, KMC-35, KMC-9C, or KMC-53
KENWOOD microphone to the MICROPHONE jack on the front
panel.
OCXO UNIT (KXK-3): Option
The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator
(OCXO) unit.
NOTICES TO THE USER
◆
Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆
Illegal operation is punishable by fine and/or imprisonment.
◆
Refer service to qualified technicians only.
◆
This repeater is intended for use as a fixed base station with
the antenna located outdoors on the rooftop or on an antenna
tower.
◆
This repeater is designed for a 13.2 V DC power source.
Never use a 24 V DC or higher source to power the repeater.
◆
Use only the supplied DC cord.
◆
Do not remove the ferrite core attached to the DC cord. Doing
so may cause interference with radio communications.
◆
Do not put anything on top of the repeater. This will obstruct
heat dissipation.
THANK YOU!
We are grateful you purchased this
KENWOOD repeater.
PRECAUTIONS
• Do not expose the unit to rain or moisture; to prevent fire or
electric shock.
• Do not open the unit under any circumstances; to avoid risk
of electric shock.
• Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
• Do not place the unit in excessively dusty and/or humid
areas, nor on unstable surfaces.
• Do not put the plastic bag used for packing of this equipment
on the place which reaches a small child's hand. It will
become a cause of suffocation if it wears flatly.
• Always switch the transceiver power off before installing
optional accessories.
• If you detect an abnormal odor or smoke coming from the
unit, disconnect the power from the unit immediately. Contact
your
KENWOOD service center or dealer.
B5A-0714-30 (E)
VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER
INSTRUCTION MANUAL
NXR-5700/ NXR-5800
◆
Do not install the repeater in explosive atmospheres
(inflammable gas, dust particles, metallic powders, grain
powders, etc.).
Information on Disposal of Old Electrical and Electronic Equipment and Batteries
(applicable for countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin)
cannot be disposed as household waste.
Old electrical and electronic equipment and batteries should be
recycled at a facility capable of handling these items and their waste
byproducts.
Contact your local authority for details in locating a recycle facility
nearest to you.
Proper recycling and waste disposal will help conserve resources
whilst preventing detrimental effects on our health and the environment.
The AMBE+2
TM
voice coding Technology embodied in this product is protected
by intellectual property rights including patent rights, copyrights and trade
secrets of Digital Voice Systems, Inc. This voice coding Technology is
licensed solely for use within this Communications Equipment. The user of
this Technology is explicitly prohibited from attempting to extract, remove,
decompile, reverse engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form. U.S. Patent Nos.
#8,315,860, #8,595,002, #6,912,495, #8,200,497, #7,970,606, and #8,359,197.
© 2019
NOTIFICATION
This equipment complies with the essential requirements of Directive
2014/53/EU.
RESTRICTIONS
This equipment requires a licence and is intended for use in the countries
as below.
AT
BE
DK
FI
FR
DE
GR
IS
IE
IT
LI
LU
NL
NO
PT
ES
SE
CH
GB
CY
CZ
EE
HU
LV
LT
MT
PL
SK
SI
BG
RO
HR
TR
ISO3166
Model
Frequency range
Max. output power
NXR-5700-E
TX/RX
136.000 - 174.000 MHz
25 W
NXR-5800-E
TX/RX
400.000 - 470.000 MHz
25 W
Firmware Copyrights
The title to and ownership of copyrights for firmware embedded in KENWOOD
product memories are reserved for JVCKENWOOD Corporation.
