Jupiter Avionics JA37-300 Скачать руководство пользователя

Страница: 9 / 26

JA37-300 Aural Message Generator - 3 Channel - Analog Inputs

Installation and Operating Manual

Rev B

Page 6

2.5.3

Message Operation

The JA37-300 Message 1, Message 2 and Message 3 audio signal playback mode are individually selectable between

Continual and One-Shot. Message playback may also be configured for Priority operation, see

section 2.5.5

–

Priority

Operation

When a message is configured as One Shot, the message audio signal is routed to the phones output for the duration

of the message. When a message is configured as Continual, the Message audio signal is routed to the phones

output for the duration of the trigger input being active.

2.5.4

Power On Self-Test Operation

When the JA37-300 power is off and then POWER INPUT is applied, the three messages will play in the following

order: message 1; message 2; message 3. The Power On Self-Test messages may be muted at any time using the

MESSAGE MUTE input. See section 2.5.2.

2.5.5

Priority Operation

When Message Trigger Priority is selected (see

Message Trigger Priority

section 2.6.

), if more than one trigger

is active, the messages will have the following priority: message 1; message 2; message 3. Note that if a higher

priority message has been triggered and is set as continual, the lower priority messages will not play until the higher

priority trigger is no longer active.

2.5.6

Non-Priority Operation

When Message Trigger Priority is configured as equal, if more than one trigger is active, the messages will play

simultaneously (both Continual and One-Shot messages).

2.5.7

RX Audio Operation

The RX 1 and 2 audio is level controlled and summed with the Message audio and routed to the Phones 1 and 2, Low

Isolation 1 and 2 outputs.

2.6

Adjustments and Configuration using ProCS™

All the JA37-300 internal adjustments are set from the

Product Configuration Software ProCS™

. Configuration data is

sent to the JA37-300 via the J2 connector, using the Configuration Cables and a computer running the ProCS™

software. For configuration cabling requirements, see

section 2.5.1

For full information on the configuration process, and for installation of ProCS™ on your computer, refer to the

ProCS™ manual

on the Jupiter Avionics website -

www.jupiteravionics.com/productsoftware.

2.6.1

Configuration Cabling Requirements

To configure the JA37-300, it is necessary to load the

Product Configuration Software ProCS™

onto a Windows-

based computer as described in the

ProCS™ manual

The cables required to configure the JA37-300 are not included with the unit.

Cabling option 1:

Quantity

Description

JAC Part #

USB A to RS232 9-Pin Cable

CAB-USB-0002

Configuration Cable

JA99-001

Cabling option 2:

Quantity

Description

JAC Part #

USB A Male to RS232 3.5mm Plug

CAB-USB-0006

Содержание JA37-300



























Результаты поиска

Содержание JA37-300

Отзывы:

Похожие инструкции для JA37-300

Бренды по названию

Популярные бренды

Jupiter Avionics JA37-300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание JA37-300

Отзывы:

Похожие инструкции для JA37-300

Бренды по названию

Популярные бренды