Juniper SRX3400 Скачать руководство пользователя страница 80

Страница: 80 / 232

Loosen the captive screws at each end of the blank faceplate over the

RE1

slot and

remove the faceplate.

Place the SCM on an antistatic mat or remove it from its electrostatic bag and place
it on the bag.

Press both of the ejector handles on the SCM faceplate outward to release them.

Orient the SCM so that its faceplate faces you. Slide the SCM all the way into the card
cage until you feel resistance. See

Figure 33 on page 66

Figure 33: Installing the SCM in the SRX3400 Services Gateway

g036099

Press both of the ejector handles inward to seat the SCM.

Tighten the screws on either side of the SCM faceplate.

Documentation

SRX3400 Services Gateway SRX Clustering Module on page 24

•

Replacing an SRX Clustering Module on the SRX3400 Services Gateway on page 120

Installing an AC Power Supply in the SRX3400 Services Gateway

NOTE:

For the services gateway to meet NEBS and ETSI standards, both AC

power supplies must be Revision 09 or later. See

“SRX3400 Services Gateway

NEBS and ETSI Compliance” on page 176

for more information.

SRX3400 Services Gateway Hardware Guide

Содержание SRX3400






















































































































































































































Результаты поиска

Содержание SRX3400

Отзывы:

Juniper SRX3400, Руководство по оборудованию, Страница: 80 / 232

Результаты поиска

Содержание SRX3400

Отзывы: