Juniper SRX3400 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 232

Juniper SRX3400 Скачать руководство пользователя страница 27

NOTE:

A minimum configuration must include one SPC and either one NPC

or one NP-IOC. However, if there are no NPCs in the chassis, the Ethernet
ports in the SFB will not be functional. See

“SRX3400 Services Gateway

Network Processing Cards” on page 20

,

“SRX3400 Services Gateway Services

Processing Cards” on page 20

for details about these cards.

Related

Documentation

SRX3400 Services Gateway Chassis on page 7

•

•

Available Components for the SRX3400 Services Gateway on page 9

•

Installing CFM Cards in the SRX3400 Services Gateway on page 59

•

Data Flow in the SRX3400 Services Gateway on page 13

•

Installation Overview for the SRX3400 Services Gateway on page 49

Data Flow in the SRX3400 Services Gateway

The services gateway receives data from the various physical interfaces on the I/O cards
(IOCs). Incoming data is passed through the Switch Fabric Board (SFB) to a Network
Processing Card (NPC), back to the SFB and on to a Services Processing Card (SPC).
The data is then passed out of the services gateway in reverse order—to the SFB, NPC,
SFB, and out to the IOC.

Related

Documentation

SRX3400 Services Gateway Chassis on page 7

•

•

Available Components for the SRX3400 Services Gateway on page 9

•

Hardware Component Locations in the SRX3400 Services Gateway Chassis on page 11

•

Installation Overview for the SRX3400 Services Gateway on page 49

SRX3400 Services Gateway Midplane

The midplane in the SRX3400 Services Gateway is in the center of the chassis and
provides connections for installing up to four common form-factor modules (CFMs)
through the front of the chassis and up to three CFMs through the rear of the chassis.
See

“Hardware Component Locations in the SRX3400 Services Gateway Chassis” on

page 11

for details about where the individual modules can be installed. The power

supplies install into the midplane from the rear of the chassis. The cooling system
components also connect to the midplane.

The midplane performs the following major functions:

•

Data path—Data packets are transferred across the midplane between the IOCs and
SPCs through the fabric ASICs on the SFBs.

•

Power distribution—The services gateway power supplies are connected to the
midplane, which distributes power to all of the services gateway components.

13

Copyright © 2013, Juniper Networks, Inc.

Chapter 2: SRX3400 Services Gateway Hardware Components

«
...
25
26
27
28
29
...
»

Содержание SRX3400









































































































































































































































Отзывы:

Нет отзывов