Juniper SRX3400 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 232

Juniper SRX3400 Скачать руководство пользователя страница 147

6.

Remove the cable lugs from the terminals.

7.

Carefully move the power cables out of the way.

8.

Push the tab on the left edge of the power supply to the right.

9.

Pull the power supply straight out of the chassis.

Figure 64: Removing a DC Power Supply

g036086

10.

Orient the replacement power supply so that the tab is on the left side, as shown in

Figure 65 on page 133

.

Figure 65: Inserting a DC Power Supply

g036085

11.

Using both hands, slide the replacement power supply straight into the chassis until
the power supply is fully seated in the chassis slot. Make sure the tab on the left edge
of the power supply clicks into place. The power supply faceplate should be flush
with any adjacent power supply faceplate.

133

Copyright © 2013, Juniper Networks, Inc.

Chapter 12: Replacing Hardware Components on the SRX3400 Services Gateway

«
...
145
146
147
148
149
...
»

Содержание SRX3400









































































































































































































































Отзывы:

Нет отзывов