Juniper SRX3400 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 232

Juniper SRX3400 Скачать руководство пользователя страница 60

To unpack the services gateway:

1.

Move the shipping carton to a staging area as close to the installation site as possible,
where you have enough room to remove the components from the chassis.

2.

Position the shipping carton with the arrows pointing up.

3.

Remove the plastic handle inserts and lift the cardboard cover off the services gateway.

4.

Remove the foam covering the top of the services gateway.

5.

Remove the accessory box, the mounting shelf, and the

SRX3400 Services Gateway

Getting Started Guide

.

Figure 22: Unpacking the SRX3400 Services Gateway

9

8

0

6

3

0

g

6.

With a person on each side of the carton, carefully lift the services gateway from the
carton and place on lift. Remove the bag covering the services gateway.

7.

Verify the parts received against the lists in

“Verifying Parts Received with the SRX3400

Services Gateway” on page 47

.

Copyright © 2013, Juniper Networks, Inc.

46

SRX3400 Services Gateway Hardware Guide

«
...
58
59
60
61
62
...
»

Содержание SRX3400









































































































































































































































Отзывы:

Нет отзывов