Juniper MX2010 Скачать руководство пользователя страница 209

Страница: 209 / 825

CHAPTER 13

DC Power Requirements, Specifications, and

Guidelines

IN THIS CHAPTER

MX2010 DC Power Requirements | 189

MX2010 DC Power Distribution Description (-48 V) | 197

MX2010 DC Power Distribution (240 V China) Description | 199

MX2010 DC Power (-48 V) System Electrical Specifications | 201

MX2010 Router DC (240 V China) System Electrical Specifications | 202

Calculating DC Power Requirements for MX2010 Routers | 204

DC Power (-48 V) Circuit Breaker Requirements for the MX2010 Router | 208

DC Power (240 V China) Circuit Breaker Requirements for the MX2000 Router | 209

DC Power Cable Specifications for the MX2010 Router | 209

MX2010 DC Power Requirements

Table 66 on page 190

lists the FRU power requirements for SFBs, CB-REs, MPCs, and MICs. In addition,

Table 66 on page 190

lists the MPC power requirements with MICs and optics at various operating

temperatures.

Typical power represents power under certain temperatures and normal operating conditions.

For PDMs with 60 A feeds, we recommend that you select the 60 A @ –48 VDC switch for each input.

For PDMs with 80 A feeds, we recommend that you select the 80 A @ –48 VDC switch for each input.

NOTE:

The 240 V China DC PDMs do not have a switch selection.

If you do not plan to provision as recommended above, you can use the information in

Table 66 on page 190

to calculate the power consumption for your hardware configuration.

189

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды