Juniper MX2010 Скачать руководство пользователя страница 229

Страница: 229 / 825

DC Power (240 V China) Circuit Breaker Requirements for the MX2000

Router

For PDMs, if you plan to operate a maximally configured DC-powered router, we recommend that you

provision at least 20 A @ 240 VDC (nominal) for each DC input to the system. Use a customer site 2 pole

circuit breaker rated according to respective National Electrical Code and customer site internal standards

to maintain proper level of protection for the current specified above.

If you plan to operate a DC-powered router at less than the maximum configuration, we recommend that

you provision a 2 pole circuit breaker according to respective National Electrical Code and customer site

internal standards to maintain proper level of protection for the current specified above .

If you plan to operate a DC-powered router at less than the maximum configuration, we recommend that

you provision a 2 pole circuit breaker according to respective National Electrical Code and customer site

internal standards to maintain proper level of protection for the current specified above or each DC power

supply rated for at least 125% of the continuous current that the system draws at 240 VDC.

DC Power Cable Specifications for the MX2010 Router

The cable lugs attach to the terminal studs of each PDM (see

Figure 75 on page 209

and

Figure 76 on page 210

NOTE:

The MX2010 supports 4-AWG DC power cable lugs for 80-A input, and 6-AWG DC

power cable lugs for 60-A input.

Figure 75: 4-AWG DC Power Cable Lug

g007054

All measurements in inches

0.63

0.25

0.27

2 holes

0.55

End view

0.09

Inner diameter .28

209

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды