Juniper MX2010 Скачать руководство пользователя страница 228

Страница: 228 / 825

MX2010 Power System Description | 95

MX2010 Power Midplane Description | 100

Overview of Preparing the Site for the MX2010 Router | 125

MX2010 DC Power Distribution Description (-48 V) | 197

MX2010 DC Power (-48 V) System Electrical Specifications | 201

DC Power (-48 V) Circuit Breaker Requirements for the MX2010 Router

For PDMs, if you plan to operate a maximally configured DC-powered router, we recommend that you

provision at least 80 A @ –48 VDC (nominal) for each DC input to the system. Use a customer-site circuit

breaker rated according to respective National Electrical Code and customer site internal standards to

maintain proper level of protection for the current specified above.

If you plan to operate a DC-powered router at less than the maximum configuration, we recommend that

you provision a circuit breaker according to respective National Electrical Code and customer-site internal

standards to maintain proper level of protection for the current specified above.

For PDMs, If you plan to operate a minimally configured DC-powered router, we recommend that you

provision at least 60 A @ –48 VDC (nominal) for each input to the system. Use a customer-site circuit

breaker rated according to National Electrical Code and customer site internal standards to maintain proper

level of protection for the current specified above.

If you plan to operate a DC-powered router at less than the maximum configuration, we recommend that

you provision a circuit breaker according to respective National Electrical Code and customer-site internal

standards to maintain proper level of protection for the current specified above or each DC power supply

rated for at least 125% of the continuous current that the system draws at –48 VDC.

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды