Juniper MX2010 Скачать руководство пользователя страница 117

Страница: 117 / 825

CHAPTER 8

Power System

IN THIS CHAPTER

MX2010 Power System Description | 95

MX2010 Power Midplane Description | 100

MX2000 Three-Phase Delta AC Power Distribution Module Description | 100

MX2000 Three-Phase Wye AC Power Distribution Module Description | 102

MX2000 Seven-Feed Single-Phase AC Power Distribution Module Description | 105

MX2000 Nine-Feed Single-Phase AC Power Distribution Module Description | 106

MX2000 Three-Phase Delta and Wye AC Power Distribution Module LEDs | 107

MX2000 AC Power Supply Module Description | 107

MX2010 AC Power Supply Module LEDs | 110

MX2010 DC Power Distribution Module (-48 V) Description | 111

MX2000 DC Power Distribution Module (240 V China) Description | 113

MX2010 DC Power Distribution Module (-48 V) LEDs | 114

MX2000 DC Power Distribution Module (240 V China) LEDs | 115

MX2010 DC Power Supply Module (-48 V) Description | 116

MX2000 DC Power Supply Module (240 V China) Description | 118

MX2010 DC Power Supply Module LEDs | 121

MX2010 Power System Description

The MX2000 routers are available in -48 V and 240 V China DC power configurations, three-phase (delta

and wye) AC power configurations, and a single-phase power configuration. You can add additional power

to the rack as needed. The MX2010 router is configurable with up to two AC or DC power distribution

modules (PDMs), and up to nine AC or DC power supply modules (PSMs). The PSMs connect to the top

and bottom power backplanes that distribute the output voltages produced by the PSMs to the router

components.

Table 30 on page 96

describes the MX2010 DC power components and

Table 31 on page 97

describes the MX2010 AC power components.

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды