manualshive.com logo in svg

Juniper MX2010, Руководство по оборудованию

Поделиться
Скачать
Juniper MX2010 Скачать руководство пользователя страница 138

Table 37: DC Power Distribution Module (240 V China) LEDs

Description

State

Color

Positive and negative input feeds are connected. PDM is functioning normally.

On

Green

Positive input feed is not connected or present.

Off

–

Negative input feed is not connected or present.

RELATED DOCUMENTATION

MX2000 Router DC (240 V China) Power Subsystem Electrical Specifications

MX2010 Component LEDs on the Craft Interface | 31

MX2010 Power System Description | 95

MX2010 DC Power (-48 V) System Electrical Specifications | 201

MX2010 DC Power Supply Module (-48 V) Description

The MX2010 supports a DC power system. The DC power system operates with feeds of 60 A or 80 A

current limited. A total of nine feeds are required to fully power the MX2010. Another nine feeds are

required to provide feed redundancy (a total of 18 60-A or 80-A feeds). In the DC power configuration,

the router contains up to nine DC PSMs located at the rear of the chassis in slots PSM0 through PSM8,

(left to right). The DC PSMs in slots PSM0 through PSM8 provide power to the all router components

including MPCs in slot 0 through 9, CB-REs in slot 0 and 1, SFBs in slot 0 through 7, and fan trays 0, 1, 2,

and 3.

NOTE:

The MX2010 systems configured for DC input power must use only DC PDMs and DC

PSMs. You cannot mix AC and DC PSMs or PDMs within a single system.

Up to nine PSMs may be connected in parallel to increase available system power across MPCs as needed

and provide redundancy.

Figure 47 on page 117

shows the DC PSM.

116

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды