Juniper MX2010 Скачать руководство пользователя страница 128

Страница: 128 / 825

Troubleshooting the MX2000 Router Power System | 320

MX2020 AC Power Requirements

MX2000 Nine-Feed Single-Phase AC Power Distribution Module Description

The MX2000 nine-feed single-phase AC power distribution module (PDM) provides AC input connection

from a single-phase AC source, and also provides an input power interface to the power supply module

(PSM) through a system power midplane. Up to nine PSMs can be connected to the single-phase AC PDM.

Each AC input is independent and feeds one PSM.

The nine-feed single-phase AC PDM weighs approximately 9 lb (4.1 kg). The front of the PDM has nine

type C21 power cord connections for connecting to single-phase AC power.

Figure 39 on page 106

shows

the nine-feed single-phase AC PDM.

Figure 39: Nine-Feed Single-Phase AC Power Distribution Module

CAUTION:

The single-phase AC PDM must be installed and secured in the chassis

before connecting the input power cables. If the PDM must be removed, all input

power cables must be removed from the PDM before the PDM can be removed from

the chassis.

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды