junger D*AP8 MAP EDITION Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 96

junger D*AP8 MAP EDITION Скачать руководство пользователя страница 20

D*AP8 MAP

18

Authentication

To prevent non authorized people from
changing D*AP8 MAP settings the
administrator may assign passwords for
either the admin and/or an operator

(same applies for talent/artist). While the admin is allowed to set everything,
an operator is just allowed to load presets. Parameters will be reset if there
was an attempt from the operator to change it.

Enable

[enable / disable]

The administrator may turn authentication off.

Change Password for [admin / operator]

Select which password you will set / change

Password

key in a password

Default passwords are: admin (for admin) and operator (for operator).

Repeat

repeat that password

Important Note! The authentication may be enabled / disabled from the console interface via USB
connection as well (see page 8 "1: Manage Password") but also via Telnet! If you have higher security
demands you should turn the Telnet server off. Authentication will be turned off and passwords will be reset if
one initializes the device to factory default (see Reboot - page 19, INIT/RESET rear button - page 4).

If there was an authentication failure, the admin will be notified
on next proper login about such conditions The pop up appears
as often as a login failed. It shows the IP address of the device
that caused the authentication failure.

After a correct login the status "who" (e.g. admin)
and a <Log Out> button are available from the GUI:

Network

IP address setup, see above:

getting started – IP setup of the MAP

–

via web browser

IP Address

The address of your choice – default [10.110.xxx.yyy]

Netmask

The net mask of your network – default [255.255.0.0]

Gateway

The optional gateway address – default [0.0.0.0]

Transmit Metering Data

[ON / OFF]

Metering data will be streamed via UDP protocol. In order to receive such
data by external applications and the GUI, you must enable it.

Service Options

Maintenance Interface [ON / OFF]
via RPC

For administrative use to enable communication with factory tools.

Telnet Server

[ON / OFF]

Enables a telnet server to connect to the consol interface via
TCP (port 23). You must be aware about the security risks if you do that
over the internet!

Diagnostics

<get diagnostics file>

It is a duplication of the soft button from the System Status pane.

«
...
18
19
20
21
22
...
»

Содержание D*AP8 MAP EDITION

































































































Отзывы:

Нет отзывов