background image

eNet radio dimming actuator 1-gang mini

Cause 2: overheating protection has tripped.

Disconnect dimmer from mains, also switch associated off circuit breakers.
HV-LED phase cut-off: Reduce the connected load. Exchange lamps for another type.
HV-LED phase cut-on: Reduce the connected load. Check operation in the "HV-LED trail-
ing edge phase control" setting. Exchange lamps for another type.
Let dimmer cool down for at least 15 minutes. Check installation situation, ensure cooling,
e.g. provide distance from surrounding devices.
Switch circuit breakers and dimmer on again.

Cause 3: Surge protection has triggered.

HV-LED trailing edge phase control: Check operation in the "HV-LED leading edge phase
control" setting, reduce connected load as well if necessary.
Exchange lamps for another type.

Cause 4: short-circuit protection has tripped.

Switch off the mains supply.
Eliminate short-circuit.
Switch circuit breakers and dimmer on again.

Short-circuit protection is not based on a conventional fuse, no metallic separation of the
operational current.

Cause 5: load failure.

Check load, replace lamp. For inductive transformers, check primary fuse and replace if
necessary.

Lamps flicker or buzz, proper dimming not possible, device buzzes

Cause 1: Incorrect operating mode set.

Check connected lamps. Correct the set operating mode.

Cause 2: Dimmer is connected without neutral conductor.

Connect neutral conductor if possible.
Exchange lamps.

LED lamp is dimly lit when dimmer is switched off

Cause: LED lamp is not optimally suited for this dimmer.

Use a compensation module, see accessories.
Use another type of LED lamp or an LED lamp of another manufacturer.

8

Accessories

eNet server for rail mounting

Art. no. ENET-SERVER

Mounting adapter for mini housing

Art. no. FM-EBG

Amplifier LED

Art. no. ULZ1755REG

Compensation module LED

Art. no. KMLED230U

9

Conformity

Albrecht Jung GmbH & Co. KG hereby declares that the radio system type art. no.
FMUD20250UP meets the directive 2014/53/EU. You can find the full article number on the
device. The complete text of the EU Declaration of Conformity is available under the Internet
address: www.jung.de/ce

10 Warranty

The warranty is provided in accordance with statutory requirements via the specialist trade.

15 / 16

82580733

14.10.2019

J0082580733

Содержание FM J 50700 UP

















Отзывы: