background image

Ceiling automatic switch 

Light Management  

Ceiling automatic switch 

Art.-No.: DAW 360 WW

Ceiling automatic switch 

Art.-No.: DAW 360 AL

Operating instructions 

1 Safety instructions 

Electrical equipment may only be installed and fitted by electrically skilled persons. 

Failure to observe the instructions may cause damage to the device and result in fire and 
other hazards. 

Danger of electric shock. Always disconnect before carrying out work on the devise or 
load. At the same time, take into account all circuit breakers that supply dangerous 
voltage to the device or load. 

Danger of electric shock. Device is not suitable for disconnection from supply voltage. 
The load is not electrically isolated from the mains even when the device is switched off. 

Do not press on the sensor window. Device can be damaged. 

The device is not suitable for use as a burglar alarm or other alarm. 

These instructions are an integral part of the product, and must remain with the end 
customer. 

2 Device components 

Figure 1 

(1)  Flush-mounted insert 
(2)  Motion detector cover 
(3)  Adjuster 

sens 

(4)  Adjuster 

time 

(5)  Adjuster 

lux 

(6)  Brightness sensor 
(7)  LED display, behind the lens 
(8)  Lens 
(9)  Decor ring 
(10) Push-on cover 

1/8 

82563813 
J:0082563813 

17.11.2011 

Содержание DAW 360 WW









Отзывы: