JUKI IT-100, Инструкция по эксплуатации

Страница: 45 / 85

– 42 –
3 Number of sttches of
reverse feed sttchng
on the way
Number of sttches of reverse feed sttchng on the way.
0 to 9
(Sttches)
N-OBT
32 Effectve condton
of reverse feed
sttchng on the
way when the
sewng machne s
stoppng.
Effectve condton of reverse feed sttchng on the way
0 : Functon s not operatve when the sewng machne stops.
: Functon s operatve when the sewng machne stops.
0/
OBTS
33 Thread trmmng
functon by reverse
feed sttchng on
the way
Thread trmmng functon by reverse feed sttchng on the way
0 : Automatc thread trmmng functon after completon of re-
verse feed sttchng on the way s not operatve.
: Automatc thread trmmng after completon of reverse feed
sttchng on the way s performed.
0/
OBTT
*
35 Sewng speed at a
low speed
Lowest speed by pedal
(The MAX value dffers by machne head.)
50 to MAX
(st/mn)
S-POS
*
3 Sewng speed of
thread trmmng
Thread trmmng speed
(The MAX value dffers by machne head.)
00 to MAX
(st/mn)
S-TRM
3 Sewng speed of
soft-start
Sewng speed at the start of sewng (soft-start)
(The MAX value dffers by machne head.)
00 to MAX
(st/mn)
S-SOFT
3 One-shot speed One-shot speed (The max. value depends on the sewng speed of
the sewng machne head.)
50 to MAX
(st/mn)
S-ASS
*
39 Pedal stroke at the
start of rotaton
Poston where the sewng machne starts rotatng from pedal neutral
poston (Pedal stroke)
0 to 50
(0. mm)
P-SSP
*
40 Low speed secton
of pedal
Poston where the sewng machne starts acceleratng from pedal
neutral poston (Pedal stroke)
0 to 00
(0. mm)
P-LSA
*
4 Startng poston of
lftng presser foot
by pedal
Poston where the cloth presser starts lftng from pedal neutral pos-
ton (Pedal stroke)
– 0 to –0
(0.mm)
P-FLW
*
42 Startng poston of
lowerng presser
foot
Startng poston of lowerng presser foot
Stroke from the neutral poston
to 50
(0. mm)
P-FLD
*
43 Pedal stroke 2 for
startng thread
trmmng
Poston 2 where the thread trmmng starts from pedal neutral pos-
ton (When the functon of lftng presser foot by pedal s provded.)
(Pedal stroke)
(Effectve only when Item No. 50 s set at .)
– 0 to –0
(0. mm)
P-TRM2
*
44 Pedal stroke
for reachng the
maxmum sewng
speed
Poston where the sewng machne reaches ts hghest sewng
speed from pedal neutral poston (Pedal stroke) 0 to 50
(0. mm)
P-MAX
*
45 Compensaton of
neutral pont of the
pedal
Compensaton value of the pedal sensor
–5 to 5
P-ANP
4 Auto-lfter selectng
functon
Lmtaton tme of watng for lftng solenod type auto-lfter devce
0 to 00
(second)
T-FL
*
4 Pedal stroke for
startng thread
trmmng
Poston where thread trmmng starts from pedal neutral poston
(Standard pedal) (Pedal stroke)
(Effectve only when Item No. 50 s set at 0.)
– 0
to – 0
(0. mm)
P-TRM
49 Lowerng tme of
presser foot
Sets the tme requred untl the lowerng of the presser foot s com-
pleted after a depress on the pedal
0
to 500
(0 ms)
T-FLWT
50 Pedal specification Type of pedal sensor s selected.
0 : KFL
: PFL
0/
PFL
5 Compensaton of
solenod-on tmng of
reverse feed sttchng
at the start of sewng
Compensaton of startng the solenod for reverse feed sttchng
when reverse feed sttchng at the start of sewng s performed.
– 3 to 3
(0°)
T-SON
52 Compensaton of
solenod-off tmng of
reverse feed sttchng
at the start of sewng
Compensaton of releasng the solenod for reverse feed sttchng
when reverse feed sttchng at the start of sewng s performed.
– 3 to 3
(0°)
T-SOFF
53 Compensaton of
solenod-off tmng of
reverse feed sttchng
at the end of sewng
Compensaton of releasng the solenod for reverse feed sttchng
when reverse feed sttchng at the end of sewng s performed.
– 3 to 3
(0°)
T-EOFF
55 Foot lft after thread
trmmng
Functon of lftng presser foot at the tme of (after) thread trmmng
0 : Not provded wth the functon of automatc lftng of work-
clamp after thread trmmng
: Provded wth the functon of lftng presser foot automatcally after
thread trmmng
0/
FLAT
5 Reverse revoluton
to lft the needle after
thread trmmng
Functon of reverse revoluton to lft the needle at the tme of (after)
thread trmmng
0 : Not provded wth the functon of reverse revoluton to lft the
needle after thread trmmng
: Provded wth the functon of reverse revoluton to lft the
needle after thread trmmng
0/
RATRM
No. Item Descrpton Settng range Indcaton of functon settng
* do not change the set values with asterisk ( * ) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer’s Manual and follow the instructions.