background image

 

 

 

 

Installation and operating instructions: JUDO potential-free fault indicator JSMP-U 1-7

 

All rights reserved. 

JUDO Wasseraufbereitung GmbH 

© JUDO Wasseraufbereitung GmbH 

Postfach 380 

 D-71351 Winnenden 

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special 
approval. 

Tel. +49 (0)7195-692-0 

 Fax +49 (0)7195-692-188 

Revision level: 13.12.2016 

E-Mail[email protected] 

 Internet: www.judo.eu 

19  

 

 

Commissioning 

 

 

Attention 

Prerequisite for commissioning is the correct installation of the JUDO fault indicator 

plus all device components!

 

 

 

The commissioning must only be performed by JUDO customer service or authorised 

technical personnel! 

Observe the separate installation and operating instructions of the corresponding water 

softening system! 

 

6.1 

Initial or recommissioning 

 
During initial or recommissioning, it must be ensured that 

no visible damage is present on the JUDO fault indicator or its device components, 

the control unit is switched on via the side toggle switch. 

 

6.2 

Faults 

 

Fault 

Cause  

Remedy 

Control unit not 
working 

Toggle switch off 

Toggle switch on 

Power supply interrupted 

Connect power supply 

Mains power connector defective 

Replace mains power connector 

Power failure 

Request JUDO customer service 

Control unit defective 

Replace control unit 

Active alarm LED 

Regeneration time exceeded 

Check water softening system 

Microswitch incorrectly connected 

Check connection 

Microswitch defective 

Replace microswitch 

Tab. 5: Faults 

 
If a fault cannot be rectified based on the information in Table 5, contact your JUDO customer service 
representative or an authorised specialist company. 
 
 

JUDO Wasseraufbereitung GmbH 

JUDO Wasseraufbereitung AG 

Winnenden Works 

Austrian subsidiary 

 

Address:  Hohreuschstraße 39-41  Zur Schleuse 5 

Industriestrasse 15 

D-71364 Winnenden 

A-2000 Stockerau 

CH-4410 Liestal 

Phone: 

+49 (0)7195-692-0 

+43 (0)2266-640-78 

+41 (0)61-90640-50 

Fax: 

+49 (0)7195-692-188 

+43 (0)2266-640-79 

+41 (0)61-90640-59 

Email: 

[email protected] 

[email protected] 

[email protected] 

Internet: 

www.judo.eu 

www.judo-online.at 

www.judo-online.ch 

 

Installation company:                                                       

 
 
 
 

Содержание JSMP-U 1





















Отзывы: