Jøtul GF 100 DV II Nordic QT Скачать руководство пользователя страница 14

14

Figure 17.  Vent Terminal Clearances - National Fuel Gas Code.

Horizontal Termination Clearance

A = Clearance above grade, veranda, porch , deck, or

balcony : 12 inches (30 cm) minimum.

B = Clearance to window or door that may be

opened: **Min. 9 inches, U.S. /  *12 inches (30 cm)
CAN.
We recommend 12in. minimum to prevent con-
densation on the window.

C = Clearance to permanently closed window:

**Min. 9 inches, U.S. /  *12 inches (30 cm) CAN
We recommend 12 in. minimum to prevent
condensation on the window.

D = Vertical clearance to ventilated soffit located

above the terminal within a horizontal distance of 2
feet (60 cm) from the centerline of the terminal: 18
inches
(46 cm) minimum.

E = Clearance to unventilated soffit:  12 inches (46

cm) minimum.

F = Clearance to outside corner: **Min. 9 inches, U.S. /

*12 inches (30 cm) CAN. We strongly recommend 12
inches, particularly where windy conditions pevail.

G = Clearance to inside corner:  ** Min. 6 inches, U.S. /

*12 inches (30 cm) CAN. We strongly recommend 12
inches, particularly where windy conditions pevail.

* In accordance with CSA B149.1 Installation Codes.

**    In accordance with the current ANSI Z223.1/NFFPA 54,
National Fuel Gas Code. Note: Local Codes and Regulations
may require different clearances.

1

 A vent shall not terminate directly above a sidewalk or

driveway which is located between two single family
dwellings and serves both dwellings.

2

Only permitted if veranda, porch, deck, or balcony, is

fully open on a minimum of two sides beneath the floor.*

H = *Not to be installed within 15 feet (4.5 m) above a

meter/regulator assembly within 3 feet (90 cm)
horizontally from the center-line of the regulator.

I = Clearance to service regulator vent outlet:

3 feet  (91 cm) minimum.

J = Clearance to nonmechanical air supply inlet to

building or the combustion air inlet to any other
appliance:
12 inches (30 cm) minimum.

K = Clearance to a mechanical air supply inlet:

**Min. 3 feet (91 cm) above if within 10 feet horizon-
tally, U.S. /  *6 feet (1.83 m) minimum / CAN

L = 

1

 Clearance above paved sidewalk or a paved driveway

located on public property: 7 feet (2.1 m) min.

M = Clearance under veranda, porch, deck, or balcony:

12 inches (30 cm) minimum.

 2

Содержание GF 100 DV II Nordic QT

































Отзывы: