Jonsered FR 2216 A 4X4 Скачать руководство пользователя страница 6

Страница: 6 / 40

–

English

KEY

O SYMBOLS

Symbols

These symbols are on the machine and in the instr

uctions.

WARNING! Careless or incorrect use can
result in serious or fatal injury to the
operator or others.

Please read the operator’s manual
carefully and make sure you understand
the instructions before using the machine.

Alw

ays wear:

•

Approved hearing protection

This product is in accordance with

applicable EC directives.

Reverse

Neutral

Fast

Slow

Stop the engine.

Batter

Chok

Fuel

Oil le

vel

Cutting height

Backwards

Forwards

Ignition

Hydrostatic free

wheel

Clutch in

Clutch out

arking brake

ake

Clutch

Noise emission to the en

vironment according

to the European Community’s Directive. The
machine’s emission is specified in chapter
Technical data and on label.

Rotar

y blades Keep hands and feet

away from under the hood when the
engine is running

Risk that the machine will tip over

Never drive across a slope

Never use the machine if persons,
especially children, or animals, are in the
vicinity

ver carry passengers on the machine or

equipment

ive very slowly if no cutting unit is fitted

Содержание FR 2216 A 4X4









































Результаты поиска

Содержание FR 2216 A 4X4

Отзывы:

Похожие инструкции для FR 2216 A 4X4

Бренды по названию

Популярные бренды

Jonsered FR 2216 A 4X4, Руководство оператора

Результаты поиска

Содержание FR 2216 A 4X4

Отзывы:

Похожие инструкции для FR 2216 A 4X4

Бренды по названию

Популярные бренды