Jonsered FR 2216 A 4X4 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

background image

26 –

English

Maintenance

Check the safety system

The machine is equipped with a safety system that prevents starting or driving under the following conditions.

The engine should only be possible to start when the cutting unit is in its raised position and the gear shift lever or hydrostat pedals
are in the neutral position.

The driver does not need to be seated in the driver’s seat.

Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not
met. Change the conditions and try again.

Check that the engine stops if you temporarily move out of the driver’s seat while the cutting unit is lowered or the gear shift lever/
hydrostat pedals are not in the neutral position.

Start motor

Ignition system

Works

Does not work

«
...
24
25
26
27
28
...
»

Содержание FR 2216 A 4X4









































Отзывы:

Нет отзывов

Похожие инструкции для FR 2216 A 4X4

Бренд: Viking Страницы: 56

Бренд: Cub Cadet Страницы: 44

Бренд: Skil Страницы: 106

Бренд: AL-KO Страницы: 116

HR 4600 Turbo 67862

Бренд: Jacobsen Страницы: 224

APACHE 1275 ZSL

Бренд: Garland Страницы: 184

Бренд: Brill Страницы: 104

Бренд: Electrolux Страницы: 49

Бренд: Electrolux Страницы: 72

Бренд: Electrolux Страницы: 88

Бренд: Electrolux Страницы: 84

Бренд: Cub Cadet Страницы: 2

Бренд: Cub Cadet Страницы: 8

Бренд: Cub Cadet Страницы: 20

Southern States SO15538LT

Бренд: Southern States Страницы: 64

Бренд: Bushranger Страницы: 14

Бренд: RC Mowers Страницы: 42

Бренд: Simplicity Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды