Jonsered CS 2152 EPA III Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 44

background image

ASSEMBLY

English

–

17

Fitting the bar and chain

Check that the chain brake is in disengaged position by
moving the front hand guard towards the front handle.

Remove the bar nuts and remove the clutch cover (chain
brake). Take off the transportation ring (A).

Fit the bar over the bar bolts. Place the bar in its rearmost
position. Place the chain over the drive sprocket locate it
in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.

Fit the clutch cover and locate the chain adjuster pin in the
hole in the bar. Check that the drive links of the chain fit
correctly over the drive sprocket and that the chain is
correctly located in the groove in the bar. Tighten the bar
nuts finger tight.

Tension the chain by turning the chain tensioning screw
clockwise using the combination spanner. The chain
should be tensioned until it does not sag from the
underside of the bar.

The chain is correctly tensioned when it does not sag from
the underside of the bar, but can still be turned easily by
hand. Hold up the bar tip and tighten the bar nuts with the
combination spanner.

When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the
chain tension regularly. A correctly tensioned chain
ensures good cutting performance and long life.

Note: If clutch cover is difficult to remove, replace bar
nuts, engage brake and rerelease (an audible click will be
heard if released properly).

!

WARNING! Always wear gloves, when
working with the chain.

A

«
...
15
16
17
18
19
...
»

Содержание CS 2152 EPA III













































Отзывы:

Нет отзывов

Похожие инструкции для CS 2152 EPA III

Бренд: Poulan Pro Страницы: 3

Бренд: Parkside Страницы: 256

Бренд: P1PE Страницы: 32

Бренд: GardenCare Страницы: 35

Бренд: Pro Work Страницы: 128

Бренд: Clinton Страницы: 16

Бренд: Hyundai power products Страницы: 48

Бренд: Jonsered Страницы: 15

Бренд: Echo Страницы: 16

Бренд: Echo Страницы: 15

Бренд: Echo Страницы: 18

Бренд: Echo Страницы: 23

Бренд: Echo Страницы: 34

Бренд: Echo Страницы: 72

Бренд: Yard Machines Страницы: 72

Бренд: North American Tool Страницы: 23

Бренд: Daewoo Страницы: 34

Patriot ES 240 PS

Бренд: Mountfield Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды