Jonsered CS 2152 EPA III Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 44

background image

MAINTENANCE

English

–

35

The filter can be cleaned more thoroughly by washing it in
water and detergent.

An air filter that has been in use for a long time cannot be
cleaned completely. The filter must therefore be replaced
with a new one at regular intervals.

A damaged air filter

must always be replaced.

A JONSERED chain saw can be equipped with different
types of air filter according to working conditions, weather,
season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•

Incorrect carburetor adjustment.

•

An incorrect fuel mixture (too much or incorrect type
of oil).

•

A dirty air filter.

These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.

If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking any further action. If the spark plug is dirty,
clean it and check that the electrode gap is 0.020 inch (0.5
mm). The spark plug should be replaced after about a
month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use
of the wrong spark plug can damage the piston/cylinder.
Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use
the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft.
This needle bearing must be lubricated regularly (once a
week). CAUTION! Use only high quality bearing grease or
engine oil. See instructions under the heading Cutting
equipment.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by
turning the screw using a screwdriver or combination
spanner. The machine is supplied from the factory with
the screw set to position 2. Turning the screw clockwise
will reduce the oil flow and turning the screw anti-
clockwise will increase the oil flow.

Recommended settings:

Bar 13"-15": Position 1

Bar 15"-18": Position 2

Bar 18"-20": Position 3

!

WARNING! The engine must be stopped
when making adjustments.

–

+

1

2

3

«
...
33
34
35
36
37
...
»

Содержание CS 2152 EPA III













































Отзывы:

Нет отзывов

Похожие инструкции для CS 2152 EPA III

Бренд: Poulan Pro Страницы: 19

20 Volt Max HT19-401-003-11

Бренд: Hyper Tough Страницы: 2

HT19-401-003-11

Бренд: Hyper Tough Страницы: 2

COMMERCIAL CS5720

Бренд: Cub Cadet Страницы: 24

Бренд: Grizzly Tools Страницы: 232

Бренд: Ryobi Страницы: 2

Бренд: Oregon Scientific Страницы: 92

Бренд: Makita Страницы: 19

Бренд: jcb Страницы: 39

Бренд: Unitec Страницы: 4

Бренд: Morrison Страницы: 16

Бренд: Challenge Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды