Jonsered 2149 Скачать руководство пользователя страница 2

Страница: 2 / 36

– English

Symbols

KEY TO SYMBOLS

Switch off the engine by moving the stop
switch to the STOP position before carrying
out any checks or maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective glasses or a visor must be worn.

CAUTION! Chain saws can be dangerous!
Careless or incorrect use can result in
serious or fatal injury to the operator or
others.

Please read the instructions carefully and
make sure you understand them before
using the saw.

Always wear:
• Approved protective helmet
• Approved hearing protection
• Protective glasses or visor

Both of the operator´s hands must be used
to operate the chain saw. Please see page
30 in your "Chain saw operator´s safety
manual".

Never operate a chain saw holding it with
one hand only. Please see page 30 in your
"Chain saw operator´s safety manual".

Contact of the guide bar tip with any object
should be avoided. Please see pages 12-21
in your "Chain saw operator´s safety
manual".

Tip contact may cause the guide bar to
move suddenly upward and backward,
which may cause serious injury. Please see
pages 12-21 in your "Chain saw operator´s
safety manual".

Содержание 2149





































Результаты поиска

Содержание 2149

Отзывы:

Похожие инструкции для 2149

Бренды по названию

Популярные бренды

Jonsered 2149, Руководство оператора

Результаты поиска

Содержание 2149

Отзывы:

Похожие инструкции для 2149

Бренды по названию

Популярные бренды