background image

English – 

35

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS
Repair or replacement of any warranted part will be perfor-
med at no charge to the owner at an approved Husqvarna AB
servicing dealer. If you have any questions regarding your
warranty rights and responsibilities, you should contact your
nearest authorized servicing dealer for Jonsered products
or call Husqvarna AB at Sweden + 46 36 14 65 00.
WARRANTY PERIOD
Any warranted part which is not scheduled for replacement
as required maintenance, or which is scheduled only for
regular inspection to the effect of ”repair or replace as
necessary” shall be warranted for 2 years. Any warranted
part which is scheduled for replacement as required
maintenance shall be warranted for the period of time up to
the first scheduled replacement point for that part.
DIAGNOSIS
The owner shall not be charged for diagnostic labor which
leads to the determination that a warranted part is defective, 
if the diagnostic work is performed at an approved Husqvarna
AB servicing dealer for Jonsered products .
CONSEQUENTIAL DAMAGES
Husqvarna AB may be liable for damages to other engine
components caused by the failure of a warranted part still
under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper
maintenance are not covered.
ADD -ON OR MODIFIED PARTS
The use of add-on or modified parts can be grounds for
disallowing a warranty claim. Husqvarna AB is not liable to
cover failures of warranted parts caused by the use of add-on
or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights
and responsibilities, you should contact your nearest
authorized servicing dealer for Jonsered products or call
Husqvarna AB at Sweden + 46 36 14 65 00.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all
Husqvarna AB authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna AB approved replacement part used in the
performance of any warranty maintenance or repairs on
emission-related parts, will be provided without charge to the
owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1. Carburetor and internal parts
2. Intake pipe, airfilter holder and carburetor bolts.
3. Airfilter and fuelfilter covered up to maintainance schedule.
4. Ignition System

a) Spark Plug, covered up to maintenance schedule
b) Ignition Module

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required
maintenance, as defined in the operator’s manual.

YOUR WARRANTY RIGHTS

AND OBLIGATIONS

The EPA (The US Environmental Protection Agency)
and Husqvarna AB are pleased to explain the emissions
control system warranty on your 1999 and later small
nonroad engine. In U.S., new small nonroad engines
must be designed, built and equipped to meet the
federal stringent anti-smog standards.
Husqvarna AB must warrant the emission control
system on your small nonroad engine for the periods of
time listed below provided there has been no abuse,
neglect or improper maintenance of your unit. Your
emission control system includes Parts such as the
carburetor and the ignition system.
Where a warrantable condition exists, Husqvarna AB
will repair your small nonroad engine at no cost to you.
Expenses covered under warranty include diagnosis,
parts and labor.

MANUFACTURER’S WARRANTY
COVERAGE

The 1999 and later small nonroad engines are warranted
for two years. If any emission related part on your
engine (as listed above) is defective, the part will be
repaired or replaced by Husqvarna AB.

OWNER’S WARRANTY
RESPONSIBILITIES

As the small nonroad engine owner, you are
responsible for the performance of the required
maintenance listed in your Operator’s Manual.
Husqvarna AB recommends that you retain all receipts
covering maintenance on your small nonroad engine,
but Husqvarna AB cannot deny warranty solely for the
lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the small nonroad engine owner, you should,
however, be aware that Husqvarna AB may deny you
warranty coverage if your small nonroad engine or a
part of it has failed due to abuse, neglect, improper
maintenance, unapproved modifications or the use of
parts not made or approved by the original equipment
manufacturer.
You are responsible for presenting your small nonroad
engine to a Husqvarna AB authorized servicing dealer
for Jonsered products as soon as a problem exists.
The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty
rights and responsibilities, you should contact your
nearest authorized servicing dealer or call Husqvarna
AB, at Sweden + 46 36 14 65 00.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad
engine is delivered.

LENGTH OF COVERAGE

Husqvarna AB warrants to the initial owner and each
subsequent purchaser that the engine is free from
defects in materials and workmanship which cause the
failure of a warranted part for a period of two years.

Содержание 2149





































Отзывы: