Johnston RT655 Скачать руководство пользователя страница 3

Страница: 3 / 58

RT655 Operator’s Guide

Johnston Sweepers Limited

Foreword

Page Issue A

Every endeavour has been made to ensure that the information contained in this Operator’s Guide

is correct, but due to continuous product development, the Company reserve the right to alter its

contents without notice. This document should not be interpreted as being part of a formal contract.

The universal safety symbol is used throughout this manual to indicate information which

is essential for health and safety for all operating personnel.

Safety Notice

Johnston

JOHNSTON

JOBRO

BROOMVAK

are registered trade marks of Johnston Sweepers Limited.

All copyrights and rights reserved. The reproduction, distribution and utilisation of this document

as well as the communication of its contents to others without express authorisation is prohibited.

of a patent, utility model or design.

For further information and enquiries please contact:

Johnston Sweepers Limited

Curtis Road, Dorking, Surrey RH4 1XF, UK
Tel: +44 (0)1306 884722

Fax: +44 (0)1306 884151

E-mail: [email protected]

Web: www.johnstonsweepers.com

Ear defenders are recommended when working around the machine

Eye protection is recommended when working around the machine

Содержание RT655



























































Результаты поиска

Содержание RT655

Отзывы:

Похожие инструкции для RT655

Бренды по названию

Популярные бренды

Johnston RT655, Руководство оператора

Результаты поиска

Содержание RT655

Отзывы:

Похожие инструкции для RT655

Бренды по названию

Популярные бренды