Johnston RT655 Скачать руководство пользователя страница 13

Страница: 13 / 58

OG2:3

RT655 Operator’s Guide

Johnston Sweepers Limited

Chapter - Controls

Page Issue A

Sweeping Controls

Symbol ID Description

Programme Button; ON/OFF switch illuminates when pressed and suspends

all sweeping and parks brushes. Pressing again reactivates previous settings.

‘Hopper Raise’ - red warning lamp and buzzer.

‘Low Air Pressure’ - amber warning lamp and buzzer.

Hydraulic Oil ‘Temperature’ - red warning lamp.

Hydraulic Oil ‘Low Level’ - amber warning lamp and buzzer.

15hrs

Rear Broom hours worked/clock.

Push button to select hourmeter reading/clock - cancels after 10 seconds.

Advance button - advances clock time when in clock setting mode.

C1 *

LH Variabrush - spring centred switch moves brush out or in.

C2 *

RH Variabrush - spring centred switch moves brush out or in.

E1/E2

LH/RH Gutter Broom 2 position switch - stowed/active illuminated when

selected.

D1 *

LH Rotatilt - spring centred switch; alters angle of Gutter broom to suit road

camber.

D2 *

RH Rotatilt - spring centred switch; alters angle of Gutter broom to suit road

camber.

J1/J2

LH/RH worklamp; 2 position switch OFF/ON. Illuminated when selected.

Front Spray Bar. 2 position switch OFF/ON illuminated when selected.

* Powathrust; - ON/OFF. Increases Channel Brush ground pressure to

preset level when on. Without the need to re-adjust the in cab regulator.

Blank.

Pick-up head and water sprays; 3 position switch - stowed/active/water

sprays. Illuminated when selected.

Pick-up head hop; 2 position - push to make stowed / CLOSED / OPEN.

Hopper Spray. 2 position switch OFF/ON illuminated when selected.

Gutter Spray. 2 position switch OFF/ON illuminated when selected.

Содержание RT655



























































Результаты поиска

Содержание RT655

Отзывы:

Похожие инструкции для RT655

Бренды по названию

Популярные бренды

Johnston RT655, Руководство оператора

Результаты поиска

Содержание RT655

Отзывы:

Похожие инструкции для RT655

Бренды по названию

Популярные бренды