Johnson T7000 PRO Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

Johnson T7000 PRO Скачать руководство пользователя страница 7

11

10

ASSEMBLY STEPS

STEP 2: Secure The Left And Right Console Mast

T R E A D M I L L T 7 0 0 0 P R O

T R E A D M I L L T 7 0 0 0 P R O

ATTENTION:

After installation is completed, the treadmill will need to be calibrated by

using the AUTO-CHECK function. If this is not done, the treadmill's speed and incline
values may be incorrect and damage the treadmill.

DO NOT

stand on the belt when

performing the AUTO-CHECK function.

STEP 1: Remove The Motor Cover

Unscrew the left and right-size screws (Z53) and lift the motor cover off the treadmill
and set it aside.

a.Attach the left console mast by placing it into the console mast support bracket and
   aligning the mounting holes.
b.Lift up the plastic piece (Q05) that is attached aside the motor cover. Place 3 screws
   (Z50) on the outside and 1 screw (Z50) on the inside and secure the screws, but leave
   room for adjustments.
c.Place a wave washer (Z51) on the screw (Z50) and secure the screw in the front of the
   console mast.
d.Put the plastic piece (Q05) down. Place 2 screws (Z53) and secure the screws into the
   frame.
e.Secure the right console mast to follow the above procedure.

Diagram 1

Z53

Z53

«
...
5
6
7
8
9
...
»

Содержание T7000 PRO

















Отзывы:

Нет отзывов