SETUP THE TREADMILL
05
04
T R E A D M I L L T 7 0 0 0 P R O
T R E A D M I L L T 7 0 0 0 P R O
GETTING STARTED
Read the Owner’s Manual before setting up the T7000 PRO. Place the treadmill where it will be
used before beginning the setup procedure.
MAKING A CHOICE OF SITE
The site that you select for the treadmill should be well-lit and well-ventilated. Locate the
T7000 PRO on a structurally solid and flat surface a few meters / feet from the wall or any equip-
ment (Allow a distance of 21 centimeters, or eight inches, between the treadmill and other
units on either side. Allow a distance of two meters, or six feet, from the rear of the tread-
mill to any object or surface.) If the site has a heavy plush carpet, to protect the carpeting
and machinery, you should place a rigid plastic base under the treadmill.
Please do not place the treadmill in an area of high humidity, such as the vicinity of a
steam room, indoor pool, or sauna. Exposure to intensive water vapor or chlorine could
adversely affect the electronics, as well as other parts of the machine. To make exercise a
desirable daily activity for you, the treadmill should be in an attractive setting.
STABILIZING THE TREADMILL
After positioning the treadmill in its intended location, check its stability by attempting to
rock it side to side. Rocking or wobbling indicates that your treadmill needs to be leveled.
Determine which leveler is not resting completely on the floor. Loosen the nut with a
hand to allow the leveler to rotate. Rotate the left or right leveler, and repeat the adjustment
as necessary until the treadmill is stable. Lock the adjustment by tightening the nut
against the rear foot support.against the rear foot support.
NOTE:
It is extremely important that the levelers are correctly adjusted for proper operation. An
unbalanced unit may cause striding belt misalignment. A bubble level is recommended to
ensure proper leveling.
• Do not remove the treadmill motor cover or roller covers. Service should be performed only
by an authorized service technician.
• Do not use any equipment that is damaged or has worn or broken parts. Use only replacement
parts supplied by Johnson Fitness or authorized dealers.
• Do not use the treadmill outdoors, near swimming pools or in areas of high humidity.
• Do not operate where aerosol (spray) products are being used or when oxygen is being
administered.
• Be sure the emergency stop pull cord is clipped to the user and in a proper placed position
on the user before beginning any workout.
• Use the stationary handrails when mount or dismount the treadmill. Place the feet firmly on
the right and left side platforms before the running belt begins moving (prior to a workout).
Step onto the running belt when the speed is at or below 1.6 km/h (1 mph).
• Never mount or dismount the treadmill while the running belt is moving.
• Handrails may be held to enhance stability as needed, but are not for continuous use.
• Do not wear any clothing that might catch on any moving parts of this treadmill.
• Never walk or jog backwards on the treadmill.
• Do not use this product in bare feet. Do not use shoes with heels, leather soles, cleats or
spikes. Make sure no stones are embedded in the soles.
• Do not turn the belt by hand.
• Close supervision is necessary when used near children, invalids or disabled people.
• When the treadmill is in use, young children and pets should be kept at least 3 meters / 10
feet away.
When it is necessary to immobilize the treadmill, set the display to read “SELECT PROGRAM OR
PRESS QUICK START”. Then hold down the "
CLEAR
" and "
ENTER
" keys at the same time. The
treadmill will now display "IMMOBILIZED". In this state, the treadmill can not be operated. Both the
drive motor & elevation motor are disabled. The treadmill will remain in this state across power
cycles, resets, etc. To return to normal operation mode repeat the same key sequence, hold
down the "
CLEAR
" and "
ENTER
" keys. The treadmill will display "SELECT PROGRAM OR PRESS
QUICK START” again.