Johnson Outdoors Scubapro S-TEK Скачать руководство пользователя страница 31

Страница: 31 / 40

English

8. OPERATION

SCUBAPRO S-Tek BC’s are supplied with the TEK BPI (K-Styled Inflator/Deflator Unit).

The TEK BPI, when connected to the tank and regulator by a Low Pressure hose,

makes it possible to control buoyancy in the water (inflation and deflation of the BC)

by using the inflate and deflate buttons.

Low Pressure (LP) Inflator hose (fig.13):
Locate the low pressure (LP) hose of the

TEK BPI Inflator/Deflator unit supplied

with your S-Tek 30,40 or 60 Wing.

Connect the LP hose to an unused LP

port of the first stage (fig 14). Note - LP

port uses a 3/8 UNF thread. Choose

the LP port that makes the most sense

for your personal configuration. This

should be torqued to 4 Newton Meters.

8.1 Connecting the TEK BPI (Inflator/Deflator Unit)

The TEK BPI allows you to inflate

your BC using gas from your SCUBA

cylinder. It’s LP hose, threaded on

an LP port of the firt stage regulator,

is connected to the TEK BPI by the

Quick Disconnect Coupling.

To attach the Quick Disconnect

Coupling:

1. Make sure that both fittings

are free of contamination prior

to connecting them together

(fig. 14-1).

2. Pull the collar of the Quick

Disconnect Coupling while

pushing the hose firmly onto

the fitting inlet on the S-TEK

inflator/deflator unit (fig. 14-2).

fig. 13

fig. 14

fig. 14-1

fig. 14-2

Содержание Scubapro S-TEK









































Результаты поиска

Содержание Scubapro S-TEK

Отзывы:

Похожие инструкции для Scubapro S-TEK

Бренды по названию

Популярные бренды

Johnson Outdoors Scubapro S-TEK, Руководство пользователя

Результаты поиска

Содержание Scubapro S-TEK

Отзывы:

Похожие инструкции для Scubapro S-TEK

Бренды по названию

Популярные бренды