background image

19

English

5.1.2   Shoulder Strap and D-Ring Location

While standing, don your harness. 

Lift your elbows ensuring your arms 

are parallel to the ground and point 

your thumb toward the shoulder 

strap (fig. 3) to get an indication of 

the correct D-ring placement.
This placement is important for 

having easy access to items clipped 

onto the D-rings, including Stage 

Cylinders.
Feed the webbing through the Tri-

Glide until you have created a loop 

(fig.3-1). Move the Tri-Glide and 

D-ring unit in the desired direction 

along the shoulder strap (fig.3-2) 

to locate it in the ideal position as 

described above.

Note:

 Before this step, decide which 

mode suits your requirement best; 

Extender or Fixed mode. WEB-LOCs 

and Tri-Glides should be removed 

or added and placed in the correct 

positions as described in the Mode 

Section above.

5.1.3   Waist D-Ring (left-side) and Tri-Glide (right-side) Position

As a general rule, the Waist D-ring on the left side 

of the S-TEK PURE Harness should be located in 

line with an outer leg trouser seam (fig.4). 

This D-ring is normally used for clipping off your 

SPG and Stage Cylinders.

In Extender Mode, the distance between the WEB-

LOC and the Waist D-ring on your left hip (or the 

Tri-Glide on your right hip), allows you to easily 

loosen Shoulder Straps to remove your harness or 

accurately tighten when donning your harness.

In Fixed Mode, the Shoulder Strap length is fixed.

To change the position, feed the webbing through 

the Tri-Glide and Tri-Glide/D-ring unit until you 

have created a loop (much the same as the 

process described above in the Shoulder Strap 

and D-ring section). Move in the desired direction 

along the Waist Strap until placement is aligned 

with an outer leg trouser seam.

fig. 3

fig. 3-1

fig. 3-2

fig. 4

Содержание Scubapro S-TEK









































Отзывы: