Setting a preloaded application
You can configure the controller to use one of the 10 preloaded applications using the MAP Gateway release 5.1 or later.
See Table 11 for the list of preloaded applications. For the application details, such as the sequence of operation and the
list of points, refer to the
VAV1717 and VAV1732 Application Note (LIT-12013794)
.
Note:
The VAV1717 controllers ship with standard application number 1, cooling only.
The VAV1732 controllers ship with a default state feature for wiring validation, see
Table 11: Preloaded applications
VAV1717
VAV1732
No. Application name
Description
No. Application name
Description
1
Cooling only
Single duct, cooling only
1
Elec Reheat 3 Stg On/Off
Parallel Fan
Staged electrical heater with
three stages and single-speed
parallel fan
2
Elec Reheat 2 Stg
Staged electrical heater with
two stages
2
Incr HW Reheat On/Off
Parallel Fan
Incremental heating water
valve and single-speed
parallel fan
3
On/Off HW Reheat
On/off heating water valve
3
Elec Reheat 3 Stg On/Off
Series Fan
Staged electrical heater with
three stages and single-speed
series fan
4
Incr HW Reheat
Incremental heating water
valve
4
Incr HW Reheat On/Off Series
Fan
Incremental heating water
valve and single-speed series
fan
5
On/Off Parallel Fan
Single-speed parallel fan
5
Var Speed Series Fan
Variable-speed series fan
6
On/Off HW Reheat On/Off
Parallel Fan
On/off heating water valve
and single-speed parallel fan
6
Elec Reheat 3 Stg Var Speed
Series Fan
Staged electrical heater with
three stages and variable-
speed series fan
7
Elec Reheat 1 Stg On/Off
Parallel Fan
Staged electrical heater with
one stage and single-speed
parallel fan
7
On/Off HW Reheat Var Speed
Series Fan
On/off heating water valve
and variable-speed series fan
8
On/Off Series Fan
Single-speed series fan
8
Incr HW Reheat Var Speed
Series Fan
Incremental heating water
valve and variable-speed
series fan
9
On/Off HW Reheat On/Off
Series Fan
On/off heating water valve
and single-speed series fan
9
Elec Reheat 3 Stg
Staged electrical heater with
three stages
10
Elec Reheat 1 Stg On/Off
Series Fan
Staged electrical heater with
one stage and single-speed
series fan
10
Proportional HW Reheat
Proportional heating water
valve
Default state for wiring validation
The VAV1732 controllers ship with a default state that
can assist in validating the wiring of the input and output
terminals before the download of an application file.
When the controller is powered on in the default state, the
fault LED flashes in a pattern of two quick blinks and then
a long pause.
To use this feature, set the DIP switches to the correct
address, and wire the input and output terminals. Apply
power to the VAV1732 controller, and connect to the
controller with either a MAP Gateway or MS-DIS1710-0
Local Display to view the points in the controller. The
controller reports an operational status, even though a
blank application is loaded. In default state, the controller
displays an application name that consists of the address
of the controller, followed by the model of the controller
and the phrase
Default State
. For example, a VAV1732
controller whose DIP switches are set to 8 has the default
state application name of
8-VAV1732 Default State
.
In the default state, input and output points appear
for all connections on the input and output terminals.
All universal inputs (UIs) appear as Nickel temperature
sensors. All configurable outputs (COs) appear as binary
outputs (BOs) with an initial value of 0. In the default
state, the device also receives input from a network
sensor at address 199.
VAV1717 and VAV1732 VAV Controllers Installation Guide
17
