background image

1083288-UIM-A-0114

34

Johnson Controls Unitary Products

NOTES:

1. Airflow expressed in standard cubic feet per minute (SCFM).
2. Motor voltage at 115 V.

SECTION IX: SAFETY CONTROLS

CONTROL CIRCUIT FUSE

A 3-amp fuse is provided on the control circuit board to protect the 24-
volt transformer from overload caused by control circuit wiring errors.
This is an ATO 3, automotive type fuse and is located on the control
board.

BLOWER DOOR SAFETY SWITCH

This unit is equipped with an electrical interlock switch mounted in the
burner compartment. This switch interrupts all power at the unit when
the panel covering the blower compartment is removed.
Electrical supply to this unit is dependent upon the panel that covers the
blower compartment being in place and properly positioned.

ROLLOUT SWITCH CONTROLS

These controls are mounted on the burner assembly. If the temperature
in the area surrounding burner exceeds its set point, the gas valve is
de-energized. The operation of this control indicates a malfunction in
the combustion air blower, heat exchanger or a blocked vent pipe con-
nection. Corrective action is required. These are manual reset controls
that must be reset before operation can continue.

Table 18: 

Blower Performance CFM - Any Position (without filter)

Models

Speed

Bottom Airflow Data (SCFM)

Ext. Static Pressure (in. H

2

O)

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

TM9X040A10MP11 

High 1290

1260

1220

1160

1100

1040

960

840

750

660

Medium High 

1170

1140

1110

1070

1040

990

930

820

730

650

Medium

990

980

940

900

860

830

790

730

680

630

Medium Low 

900

880

850

810

770

730

670

630

600

560

Low 730

710

690

650

620

590

540

510

480

450

TM9X060B12MP11 

High 1402

1374

1354

1328

1299

1262

1222

1167

1107

1036

Medium High 

1252

1233

1203

1182

1150

1125

1095

1064

1031

980

Medium

1076

1059

1029

1007

973

946

908

883

843

800

Medium Low 

988

967

936

903

875

838

806

765

737

685

Low 798

769

727

695

650

619

574

517

485

443

TM9X080B12MP11 

High 1445

1423

1397

1365

1339

1311

1283

1250

1204

1140

Medium High 

1282

1266

1232

1211

1182

1157

1128

1097

1069

1013

Medium

1098

1084

1059

1027

998

967

939

910

879

822

Medium Low 

1012

993

953

930

894

851

828

773

752

692

Low 865

810

763

730

689

628

594

520

496

448

TM9X080C16MP11 

High 1713

1682

1643

1600

1558

1519

1480

1436

1385

1333

Medium High 

1554

1519

1485

1439

1404

1368

1327

1280

1176

1130

Medium

1380

1351

1302

1263

1224

1171

1128

1085

1030

943

Medium Low 

1177

1142

1083

1050

988

922

890

819

798

687

Low 

951

841

650

588

457

418

355

227

203

N / A

TM9X100C16MP11 

High 1734

1694

1650

1611

1570

1536

1485

1438

1392

1335

Medium High 

1568

1537

1492

1453

1414

1373

1327

1279

1230

1118

Medium

1420

1380

1332

1294

1249

1196

1152

1100

981

938

Medium 1218

1169

1124

1067

1015

965

894

845

754

679

Low 

979

846

647

580

464

427

345

220

195

N / A

TM9X100C20MP11 

High 2143

2102

2065

2028

1989

1944

1892

1825

1733

1625

Medium High 

1788

1749

1718

1672

1629

1587

1541

1500

1447

1355

Medium

1575

1539

1500

1456

1410

1363

1305

1246

1095

1030

Medium Low 

1372

1325

1276

1225

1170

1111

1044

972

884

812

Low 1031

921

810

728

660

615

518

474

391

355

TM9X120D20MP11 

High 2214

2173

2132

2086

2036

1994

1952

1907

1849

1777

Medium High 

1841

1799

1749

1699

1659

1611

1567

1520

1471

1372

Medium

1605

1562

1514

1470

1416

1361

1310

1180

1119

1045

Medium Low 

1405

1362

1303

1244

1189

1125

1054

986

876

826

Low 

1135

1020

844

758

671

557

511

464

387

N / A

Main power to the unit must still be interrupted at the main power dis-
connect switch before any service or repair work is to be done to the
unit. Do not rely upon the interlock switch as a main power discon-
nect.
Blower and burner must never be operated without the blower panel
in place.

Содержание TM9X









































Отзывы: