background image

TM-11x1 Series Room Temperature Module Installation Instructions 

3

Installing the TM-11x1

To install the TM-11x1 Series Room Temperature 
Module:

1.

Use the Allen-head tool to loosen the security 
screw located at the top center of the housing.

2.

Insert a screwdriver blade or coin into the slot on 
the top of the housing.

3.

Press down gently, and pry the housing away from 
the base. As the two parts separate, remove the 
blade or coin and continue to pull the housing away 
from the base until the housing is free.

4.

Pull the wires through the base. Locate the green 

terminal blocks in the upper right of the base and 

position the module on the wallbox with the 

terminal numbers right-side up.

5.

Mount the base to the wallbox using the two #6-32 
mounting screws (included).

6.

Wire the controller to the module. See the 

Wiring

 

section for correct wiring.

7.

Attach the housing to the base and tighten the 
security screw with the allen-head tool.

Mounting

Location Considerations

Mount the TM-11x1 Series Room Temperature Module 
on a wall in the room to be controlled. Locate it where 
the occupant can easily read and adjust the setpoint 
dial or fan speed override adjustment dial. Consider 
these additional guidelines to determine the best 
mounting location:

Avoid areas subject to excessive vibration, 
electrical noise, direct sunlight, or the effects of 
radiant heat.

Keep electrical wiring as short as possible to 
minimize temperature error.

Install modules in areas where the temperature is 
representative of the general room conditions.

Wiring

To wire a TC-9102 Controller to the TM-11x1 Series 
Room Temperature Module, see the appropriate wiring 
diagram (Figure 5 to Figure 9). 

Note:

Use 22 AWG (0.65 mm diameter) wire 

minimum. Do not exceed 164 ft (50 m) between the 
controller and the temperature module.

Table 1:  Nominal Values for Sensors

Temperature

Resistance

F

C

ohm

20

-7

10,595.0

30

-1

7,739.2

40

4

6,010.0

50

10

4,482.3

60

16

3,378.3

70

21

2,689.6

80

27

2,063.9

90

32

1,666.9

100

38

1,300.2

110

43

1,063.9

120

49

842.47

130

54

697.65

Содержание TM-11x1 series







Отзывы: