Johnson Controls TEC2102-3 Скачать руководство пользователя страница 14

Страница: 14 / 17

TEC2102-3 N2 Networked Heat Pump Thermostat Installation Instructions

To enter the permanent heating and cooling setpoints
for the Occupied and Unoccupied Modes, follow the
steps in Table 3. When changing the temperatures,
press the keys once to change the temperature in
0.5F°/0.5C° increments; press and hold down the keys
to change the temperature in 5.0F°/5.0C° increments.

Entering Temporary Temperature Setpoints

To temporarily change the setpoint, press the

UP/DOWN

arrow keys to change the temporary

setpoint for the current mode of operation.

Note:

Whether the thermostat is heating or cooling,

the respective setpoint is temporarily adjusted. To
toggle between the temporary heating and cooling
setpoints, press the

key while changing the

temporary setpoints.

Ending Temporary Temperature Setpoints

The temporary setpoints remain in effect for the
duration set in the

TOccTime

parameter or until

manually released.

To release the temporary setpoint sooner, while in the
Main User Menu:

Press the

YES

key to the first prompt that appears.

If the thermostat does not immediately return to the
Status Display Menu, press the

MENU

key again

and press the

YES

key to exit the Main User Menu.

The setpoint reverts to the Permanent Temperature
Setpoint.

Table 3: Entering Permanent Temperature

Setpoints (Part 1 of 2)

Thermostat
Display

Description

Press the

MENU

key while in the

Status Display Menu to enter the
Main User Menu.

Press the

key to all prompts until

the temperature setpoint prompt
appears on the display (it may be the
first prompt). Press the

YES

key to

enter the temperature setting menu.

Press the

YES

key to change the

occupied cooling setpoint. Press the

key to advance to the occupied

heating setpoint menu.

Press the

UP/DOWN

arrow keys to

set the temperature. Press the

YES

key to store the value and advance to
the next menu.

Press the

YES

key to change the

occupied heating setpoint. Press the

key to advance to the unoccupied

cooling setpoint menu.

Press the

UP/DOWN

arrow keys to

set the temperature. Press the

YES

key to store the value and advance to
the next menu.

Press the

YES

key to change the

unoccupied cooling setpoint. Press
the

key to advance to the

unoccupied heating setpoint.

Press the

UP/DOWN

arrow keys to

set the temperature. Press the

YES

key to store the value and advance to
the next menu.

RoomTemp
75.0

Temperat
set? Y/N

Cooling
set? Y/N

Cooling
75.0

Heating
set? Y/N

Heating
68.0

Unocc CL
set? Y/N

Unocc CL
80.0

Press the

YES

key to change the

unoccupied heating setpoint. Press
the

key to advance to the

temperature display units.

Press the

UP/DOWN

arrow keys to

set the temperature. Press the

YES

key to store the value and advance to
the next menu.

Press the

YES

key to set the display

units to °F or °C. Press the

key to

advance to the temperature setpoint
type menu.

Press the

YES

key to return to the

Status Display Menu or press the

key to reenter the temperature
setting menu.

Table 3: Entering Permanent Temperature

Setpoints (Part 2 of 2)

Thermostat
Display

Description

Unocc HT
set? Y/N

Unocc HT
62.0

set? Y/N

Exit?
Y/N

Содержание TEC2102-3


















Результаты поиска

Содержание TEC2102-3

Отзывы:

Похожие инструкции для TEC2102-3

Бренды по названию

Популярные бренды

Johnson Controls TEC2102-3, Руководство по установке

Результаты поиска

Содержание TEC2102-3

Отзывы:

Похожие инструкции для TEC2102-3

Бренды по названию

Популярные бренды