Johnson Controls PCV1617 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

Johnson Controls PCV1617 Скачать руководство пользователя страница 10

CAUTION

Risque de dommages matériels:

Ne mettez pas l’appareil sous tension avant d’avoir vérifié toutes les connexions du câblage. Le câblage

inadéquat de cette borne peut causer un court-circuit sur l’alimentation électrique de 24 V c.a. des

PCV 16xx-1 modèles. Un court-circuit peut causer le déclenchement du disjoncteur ou le grillage d’un

fusible. Si vous utilisez un transformateur avec un fusible intégré, vous pourriez devoir remplacer le

transformateur.

To wire the PCV1617 or PCV1632 controller:

1. Terminate wiring according to the appropriate figure in

Termination diagrams

2.  Wire network sensors and other devices to the PCV's SA Bus.
3.  Wire the FC Bus in a daisy chain.
4.  Ensure that the PCV’s device address DIP switches are set to the appropriate device address.

Setting the device address

. Also, activate the end-of-line (EOL) switch if necessary.

5. Connect the PCV controller to 24 VAC, Class 2 power.

PCV terminal functions, ratings, requirements, and wiring

guidelines

Input and Output wiring guidelines

Table 2 provides information about the functions, ratings, and requirements for the PCV input and

output terminals, and Table 3 provides guidelines for wire sizes and cable lengths.
In addition to the wiring guidelines in Table 2, observe these guidelines when wiring PCV inputs and

outputs:
• Run all low-voltage wiring and cables separate from high-voltage wiring.
• All input and output cables, regardless of wire size or number of wires, should consist of twisted,

insulated, and stranded copper wires.

• Shielded cable is recommended for input and output cables that are exposed to high

electromagnetic or radio frequency noise.

• Cable runs of less than 30 m (100 ft) typically do not require an offset in the input/output

software setup. Cable runs over 30 m (100 ft) may require an offset in the input/output software

setup.

Maximum cable length versus load current

Use Figure 8 to estimate the maximum cable length relative to the wire size and the load current (in

mA) when wiring inputs and outputs.

FC and SA bus and supply power wiring guidelines

Table 5 provides information about terminal block functions, ratings, and requirements.
Table 5 also provides wire size, cable type, and cable length guidelines for wiring the PCV

communication buses and supply power.

PCV1617 and PCV1632 VAV Box Controllers Installation instructions

10

«
...
8
9
10
11
12
...
»

Содержание PCV1617





























Отзывы:

Нет отзывов