manualshive.com logo in svg

Johnson Controls PCV1617, Руководство по установке, Страница: 13 / 28

Поделиться
Скачать
Johnson Controls PCV1617 Скачать руководство пользователя страница 13

Table 2: I/O terminal blocks, functions, ratings, requirements, and cables

Terminal block

label

Terminal

labels

Function, ratings, and

requirements

To determine wire

size and maximum
cable length 

1

1

Binary Output Signal Common

:

All Configurable Outputs defined

as Binary Outputs are isolated from

all other commons, including other

Configurable Output commons.

1

Table 3 defines cable length guidelines for the various wire sizes that may be used for input and output wiring.

Table 3: Cable length guidelines for recommended wire sizes

Guideline

Wire size/Gauge and

type

Maximum cable

length and type

Assumptions

1.5 mm (16 AWG)

stranded copper

457 m (1,500 ft) twisted

wire

0.8 mm (20 AWG)

stranded copper 297 m

(975 ft) twisted wire

297 m (975 ft) twisted

wire

0.6 mm (22 AWG)

stranded copper 183 m

(600 ft) twisted wire

183 m (600 ft) twisted

wire

A

N/A (24 AWG) stranded

copper 107 m (350 ft)

twisted wire

107 m (350 ft) twisted

wire

100 mV maximum

voltage drop
Depending on the

cable length and the

connected input or

output device, you may

have to define an offset

in the setup software

for the input or output

point.

1.5 mm (18 AWG)

stranded copper

229 m (750 ft) twisted

wire

0.8 mm (20 AWG)

stranded copper 297 m

(975 ft) twisted wire

137 m (450 ft) twisted

wire

0.6 mm (22 AWG)

stranded copper 183 m

(600 ft) twisted wire

91 m (300 ft) twisted

wire

B

24 AWG stranded copper

107 m (350 ft) twisted

wire

61 m (200 ft) twisted

wire

100 mV maximum

voltage drop
Depending on the

cable length and the

connected input or

output device, you may

have to define an offset

in the setup software

for the input or output

point.

C

See Figure 8 to select

wire size/gauge.
Use stranded copper

wire.

See Figure 8 to

determine cable

length.
Use twisted wire cable.

N/A

Termination diagrams

A set of Johnson Controls termination diagrams provides details for wiring inputs and outputs to

the controllers. See the figures in this section for the applicable termination diagrams.

13

PCV1617 and PCV1632 VAV Box Controllers Installation instructions

Содержание PCV1617





























Отзывы:

Нет отзывов