manualshive.com logo in svg

Johnson Controls PCV1617, Руководство по установке, Страница: 11 / 28

Поделиться
Скачать
Johnson Controls PCV1617 Скачать руководство пользователя страница 11

In addition to the guidelines in Table 5, observe these guidelines when wiring the SA/FC Buses and

supply power:
• Run 

all

 low-voltage wiring and cables separate from high-voltage wiring.

• All FC and SA Bus cables, regardless of wire size, should be twisted, insulated, stranded copper

wire.

• Shielded cable is strongly recommended for all FC and SA Bus cables.

Input and Output wiring guidelines tables

Table 2: I/O terminal blocks, functions, ratings, requirements, and cables

Terminal block

label

Terminal

labels

Function, ratings, and

requirements

To determine wire

size and maximum
cable length 

1

1

+15 V

15 VDC Power Source

 for active (3-

wire) input devices connected to the

Universal INn terminals.
Provides 35 mA total current.

Same as (Universal)

IN

n

.

Note: 

Use 3-wire

cable for devices

that source power

from the +15 V

terminal.

Analog Input - Voltage Mode (0–10

VDC)

10 VDC maximum input voltage
Internal 75k ohm Pulldown

See Guideline A in

Table 3.

Analog Input - Resistive Mode (0–

600k ohm)

Internal 12 V, 15k ohm pull up
Qualified Sensors: 0–2k

potentiometer,
RTD (1k Nickel [ Johnson Controls

®

sensor],
1k Platinum, and A99B Silicon

Temperature Sensor)
Negative Temperature Coefficient

(NTC) Sensor
10K Type L (10K JCI Type II is

equivalent to Type L) or 2.252K Type

II

See Guideline A in

Table 3.

UNIVERSAL

(Inputs)

IN

n

Binary Input - Dry Contact

Maintained Mode

1 second minimum pulse width
Internal 12 V, 15k ohm pull up

See Guideline A in

Table 3.

11

PCV1617 and PCV1632 VAV Box Controllers Installation instructions

Содержание PCV1617





























Отзывы:

Нет отзывов