manualshive.com logo in svg

Johnson Controls PCV1617, Руководство по установке, Страница: 8 / 28

Поделиться
Скачать
Johnson Controls PCV1617 Скачать руководство пользователя страница 8

Figure  4: SA bus terminal block wiring

Modular port

The modular (TSTAT) port on the face of the PCV (Figure 2) is an RJ-45, 8-position modular jack used

to easily connect one TE-730 series analog (non-communicating) sensor to the PCV. The modular

TSTAT port provides 15 VDC, SA Bus communications, and analog signals for zone temperature,

zone setpoint, and temporary zone occupancy override.

Note: 

 On the TE-730 Series sensors, you can activate the occupancy override functionality by

using a pushbutton to momentarily short the zone temperature AI.

The TSTAT pin assignment is shown in Figure 5.

Note: 

Do not use the modular SA Bus port and the terminal block SA Bus simultaneously. Only

use one of these connections at a time.

Figure  5: Pin number assignments for the

modular port on PCV1617 and PCV1632 Controllers

Supply power terminal block

The 24 VAC supply power terminal block is a gray, removable, 2-terminal plug that fits into a board-

mounted jack on the upper left of the PCV controller.

PCV1617 and PCV1632 VAV Box Controllers Installation instructions

8

Содержание PCV1617





























Отзывы:

Нет отзывов