manualshive.com logo in svg

Johnson Controls PCA3613, Руководство по установке, Страница: 29 / 30

Поделиться
Скачать
Johnson Controls PCA3613 Скачать руководство пользователя страница 29

Table 10: PCA3613 Advanced Application Programmable Controller

Input and Output Capabilities 8 - Universal Inputs:

 Defined as 0–10 VDC, 4–20 mA, 0–600k

ohms, or Binary Dry Contact

6 - Binary Inputs:

 Defined as Dry Contact Maintained or Pulse

Counter/Accumulator Mode

6 - Binary Outputs: 

 Defined as 24 VAC Triac (external power

source only)

6 - Analog Outputs:

 Defined as 0–10 VDC or 4–20 mA

Analog Input/Analog Output

Resolution and Accuracy

Input: 

15-bit resolution

Output:

 15-bit resolution, +/- 200 mV accuracy in 0–10 VDC

applications

Terminations

Input/Output:

 Fixed Screw Terminal Blocks

SA/FC Bus and Supply Power:

 4-Wire and 3-Wire Pluggable

Screw Terminal Blocks

SA/FC Bus Port:

 RJ-12 6-Pin Modular Jacks

Mounting

Horizontal on single 35 mm DIN rail mount (preferred), or screw

mount on flat surface with three integral mounting clips on

controller

Housing

Enclosure material:

 ABS and polycarbonate UL94 5VB; Self-

extinguishing
Protection Class: IP20 (IEC529)

Dimensions (Height x Width x

Depth)

150 mm x 220 mm x 57.5 mm (5-7/8 in. x 8-3/4 in. x 2-3/8 in.)

including terminals and mounting clips

Note: 

Mounting space requires an additional 50 mm (2 in.)

space on top, bottom, and front face of controller for easy

cover removal, ventilation, and wire terminations.

Weight

0.5 kg (1.1 lb)

United States:

 UL Listed, File E107041, CCN PAZX, UL 916,

Energy Management Equipment
FCC Compliant to CFR47, Part 15, Subpart B, Class A

Canada:

 UL Listed, File E107041, CCN PAZX7 CAN/CSA C22.2 No.

205, Signal Equipment
Industry Canada Compliant, ICES-003

Europe:

 Johnson Controls declares that this product is in

compliance with the essential requirements and other relevant

provisions of the EMC Directive.

Australia and New Zealand:

 RCM Mark, Australia/NZ Emissions

Compliant

Compliance

BACnet International:

 BACnet Testing Laboratories™ (BTL)

Protocol Revision 15 Listed and Certified BACnet Advanced

Application Controller (B-AAC), based on the ANSI/ASHRAE

135-2016

29

PCA3613 Advanced Application Programmable Controller Installation Instructions

Содержание PCA3613































Отзывы:

Нет отзывов