Johnson Controls PCA3613 Скачать руководство пользователя страница 27

Страница: 27 / 30

Table 8: Status LEDs and description of LED states

LED label

LED

color

Normal LED

state

Description of LED states

FC BUS

Green

Blink - 2 Hz

Blink - 2 Hz = Data Transmission (normal communication)
Off Steady = No Data Transmission (auto baud in progress)
On Steady = Communication lost, waiting to join

communication ring

EOL

Amber

Off

(Except on

terminating

devices)

On Steady = EOL switch in ON position
Off Steady = EOL switch in Off position

Repair information

If the PCA3613 controller fails to operate within its specifications, replace the controller. For a

replacement controller, contact your Johnson Controls representative.

Accessories

Table 9: Accessories ordering information

Product code

number

Description

PCX Series

Modules

Depending on your system (FX or BCPro), refer to the

CH-PC Series

Programmable Controllers and Related Products for the BCPro System Product

Bulletin (LIT-12011914)

FX-PC Series Programmable Controllers and Related

Products Product Bulletin (LIT-12011657)

for a complete list of available PCX

Series Controllers.

NS Series

Sensors

Refer to the

NS Series Network Sensors Product Bulletin (LIT-12011574)

for a

complete list of available NS Series Sensors.

TL-MAP1810-0PA

Portable MAP Gateway for Asia (China, Japan, Australia, New Zealand, India,

Singapore, Thailand, Hong Kong)

FX-DIS1710-0

Local Controller Display

TP-2420

Transformer, 120 VAC Primary to 24 VAC secondary, 20 VA, Wall Plug

Y65T31-0

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Foot

Mount, 8 in. Primary Leads and Secondary Screw Terminals, Class 2

Note:

Additional Y6x-x Series transformers are also available. Refer to the

Series Y63, Y64, Y65, Y66, and Y69 Transformers Product Bulletin (LIT-125755)

for more information.

AS-XFR050-0

Power transformer (Class 2, 24 VAC, 50 VA maximum output), no enclosure

AS-CBLSTAT-0

Cable adapter for connecting to 8-pin TE-6700 Series sensors

AP-TBK4SA-0

Replacement SA Bus Terminal Blocks, 4-Position, Brown, Bulk Pack of 10

AP-TBK4FC-0

Replacement FC Bus Terminal Blocks, 4-Position, Blue, Bulk Pack of 10

AP-TBK3PW-0

Replacement Power Terminal Blocks, 3-Position, Gray, Bulk Pack of 10

PCA3613 Advanced Application Programmable Controller Installation Instructions

Содержание PCA3613































Результаты поиска

Содержание PCA3613

Отзывы:

Похожие инструкции для PCA3613

Бренды по названию

Популярные бренды

Johnson Controls PCA3613, Руководство по установке

Результаты поиска

Содержание PCA3613

Отзывы:

Похожие инструкции для PCA3613

Бренды по названию

Популярные бренды