manualshive.com logo in svg

Johnson Controls PCA3613, Руководство по установке, Страница: 23 / 30

Поделиться
Скачать
Johnson Controls PCA3613 Скачать руководство пользователя страница 23

Table 6: SA/FC bus device address descriptions

Device address

Use on description

0

(Switch 128 Off)

Reserved for FC Bus Supervisory Controller (not for use on controllers).

1 to 3

(Switch 128 Off)

Reserved for peripheral devices (not for use on controllers).

4 to 127

(Switch 128 Off)

Used for MS/TP master devices (controllers) that are hardwired to an SA bus or

FC bus.

0 to 3

(Switch 128 ON)

Reserved addresses for wired subordinate devices (not for use on controllers).

Note: 

 controllers ship with switch 128 ON and the remaining address

switches off rendering the controllers wired subordinate devices, which

do not operate on MS/TP buses.

4 to 127

(Switch 128 ON)

Valid for MS/TP Master controllers on 

wireless FC Buses only

.

Note: 

Do 

not

 connect a controller with switch 128 ON to an active (

hard-

wired

) SA or FC bus. When a controller with switch 128 ON and a device

address from 4 to 127 is connected to a wired field bus, the entire field

bus is rendered inoperable until the controller is disconnected or switch

128 is set to 

Off

.

Removing the Controller cover

Important: 

Electrostatic discharge can damage controller components. Use proper

electrostatic discharge precautions during installation, setup, and servicing to avoid damaging

the controller.

Important: 

Disconnect all power sources to the controller before you remove the cover

and change the position of any jumper on the controller. Failure to disconnect power before

changing a jumper can result in damage to the controller and void any warranties.

The controller cover is held in place by four plastic latches that extend from the base and snap into

slots on the inside of the housing cover.
To remove the controller cover, complete the following steps:
1. Place your fingertips under the two cover lift tabs on the sides of the housing cover and gently

pry the top of the cover away from the base to release the cover from the two upper latches.

2. Pivot the top of the cover further to release it from the lower two latches.
3. Replace the cover by placing it squarely over the base, and then gently and evenly push the

cover on to the latches until they snap into the latched position.

23

PCA3613 Advanced Application Programmable Controller Installation Instructions

Содержание PCA3613































Отзывы:

Нет отзывов