background image

M9220-GGx-3 Proportional Electric Spring Return Actuators Installation Instructions

11

Tandem Operation: GGx Master with 
GGx Slaves

The tandem configuration (Figure 14 and Figure 16) 
provides twice (with two actuators) or triple (with three 
actuators) the running and spring return torque of a 
single actuator, or 354 lb·in (40 N·m), 531 lb·in 
(60 N·m). The actuators may be mounted in tandem 
using the M9000-158 Tandem Mounting Kit. To mount 
a third actuator, user-configured bracketing is required.

Follow these guidelines for tandem operation:

Two or three M9220-GGx-3 actuators may be 
operated in tandem on the same shaft. If mounting 
two actuators, see Figure 14; for three actuators, 
see Figure 16.

Each actuator requires separate 24 volt power. 
When two or more actuators connected in tandem 
share a common power source, the total maximum 
power draw is actually 1.5 times the normal 
running current for each actuator. 
(Total Power = Number of Actuators x Running 
Power x 1.5).

Only one of the actuators can be configured as the 
master. Set the selector switch to the master 
position (Figure 15).       

The other GGx actuator(s) 

must

 be configured as 

slave(s), by setting the tandem selector switch to 
the slave position.

The master can accept DC 0-10 V or DC 2-10 V, or 
4-20 mA command signals based on the master’s 
switch settings and/or external resistor.

The master and slave(s) must have matching 
RA/DA settings.

Figure 14: Tandem Connection

F

IG

:t

an

d

em

1

Master

(M9220GGx actuator)

DC 0(2)...10V Control with Tandem Connection

Slave

(

 only)

M9220GGx actuator

Y

DC 0(2)...10 V

+

U

+

1

2

3

4

BLK RED GRY ORN

AC/DC

24 v

~

(+)

DC 0(2)...10 V

COM

+

1

2

3

4

BLK RED GRY ORN

se

le

c

t

Side A of Actuator

Side B of Actuator

Figure 15: Tandem Selector Switch

Figure 16: Tandem Connection with Three Actuators

F

IG

:t

an

d

2

Y

DC 0(2)...10 V

+

Master

(M9220GGx actuator)

U

+

1

2

3

4

BLK RED GRY ORN

DC 0(2)...10V Control with Multiple Slaves

Slave

(

only)

M9220GGx actuator 

AC/DC

24 V

~

(+)

DC 0(2)...10 V

COM

+

1

2

3

4

BLK RED GRY ORN

Slave

(

 

only)

M9220GGx actuator

+

1

2

3

4

BLK RED GRY ORN

Содержание M9220-GGx-3 series
















Отзывы: