manualshive.com logo in svg

Johnson Controls GS3000, Руководство по установке, Страница: 13 / 18

Поделиться
Скачать
Johnson Controls GS3000 Скачать руководство пользователя страница 13

Table 2: GS3000 Gas Detection Sensor Series setup menu

Specification

Requirements

Description

NO

2

 recal mode

Only if you install the NO

2

 Sensor

The default setting is 1 year. Use the 

UP

 or

DOWN

 buttons to set the NO

2

 recalibration

mode timer to disable, 1, 2, 3 years, or reset.

When disabled, the device does not sound

the buzzer or provide LCD and status LED

indication when the NO

2

 sensor requires

recalibration.

When set to 1, 2 or 3 years, the ReCal alarm

activates to indicate that the NO

2

 sensor

requires recalibration. If set to reset and you

press the 

MENU

, the ReCal condition for

the NO

2

 sensor clears, the NO

2

 ReCal timer

resets, and the NO ReCal mode remains at

the previous setting. The timer automatically

resets if you replace the NO

2

 sensor. If the

preferred time has already been exceeded,

you cannot select it. If the NO

2

 sensor is

calibrated with gas through the 

MENU

, the

timer automatically resets.

Alarm mode

The default setting is Auto. Use the 

UP

or 

DOWN

 buttons to set the Alarm Mode

to Auto or Manual. This setting controls

how Alarm 1, Alarm 2, and the buzzer

alarm resets back to normal mode. For the

Auto setting, the device resets the alarms

automatically once the gas level drops below

the set alarm thresholds.

For the manual setting, the gas level must

be below the alarm thresholds and you must

press the 

TEST

 switch on the device to reset

the alarms.

CO zero filter

Only if you install the CO sensor

Use the 

UP

 or 

DOWN

 buttons to turn ON or

OFF the CO zero filter. When ON, the device

filters low ppm readings such that 0 ppm to

5 ppm CO displays and output 0 ppm. When

OFF, 0 ppm to 5 ppm displays and output

actual 0 ppm to 5 ppm. The factory default

setting is ON.

Note: 

The zero filter is automatically

disabled when performing a CO gas

calibration.

NO

2

 zero filter

Only if you install the NO

2

 sensor

Use the 

UP

 or 

DOWN

 buttons to turn ON or

OFF the NO

2

 zero filter. When ON, the device

filters low ppm readings such that 0 ppm

to 0.5 ppm NO

2

 displays and output 0 ppm.

When OFF, 0 ppm to 0.5 ppm displays and

output actual 0 ppm to 0.5 ppm. The default

setting is ON.

Note: 

The zero filter automatically

disables when performing a NO

2

 gas

calibration.

GS3000 Gas Detection Sensor Series Installation Guide

13

Содержание GS3000



















Отзывы:

Нет отзывов