background image

Table 1: I/O Terminal Blocks, Functions, Ratings, Requirements, and Cables

To Determine Wire Size
and Maximum Cable

Length

1

Function, Ratings, and Requirements

Terminal
Labels

Terminal Block Label

See Guideline A in

Table 2

.

Analog Output - Voltage Mode (0–10 VDC)

10 VDC maximum output voltage

10 mA maximum output current

External 1k to 50k ohm load required

OUTn

CONFIGURABLE

(Outputs)

See Guideline C in

Table 2

.

Binary Output 24 VAC Triac

Connects OUT to OCOM when activated.

External Power Source:

30 VAC maximum voltage to load

0.5 A maximum output current

1.3 A at 25% duty cycle

40 mA minimum load current

Same as (Configurable)

OUTn

.

Analog Output Signal Common

: All

Configurable Outputs defined as Analog Outputs
share a common, which is isolated from all other
commons except the Binary Input common.

OCOMn

Binary Output Signal Common

: All

Configurable Outputs defined as Binary Outputs
are isolated from all other commons, including
other Configurable Output commons.

1

Table 2

defines cable length guidelines for the various wire sizes that may be used for input and output wiring.

Table 2: Cable Length Guidelines for Recommended Wire Sizes

Assumptions

Maximum Cable Length
and Type

Wire Size/Gauge and Type

Guideline

100 mV maximum voltage drop

Depending on the cable length
and the connected input or
output device, you may have to
define an offset in the setup
software for the input or output
point.

457 m (1,500 ft) twisted wire

1.5 mm

2

(18 AWG) stranded

copper

A

297 m (975 ft) twisted wire

0.8 mm (20 AWG) stranded copper
297 m (975 ft) twisted wire

183 m (600 ft) twisted wire

0.6 mm (22 AWG) stranded copper
183 m (600 ft) twisted wire

107 m (350 ft) twisted wire

24 AWG stranded copper 107 m
(350 ft) twisted wire

100 mV maximum voltage drop

Depending on the cable length
and the connected input or
output device, you may have to
define an offset in the setup
software for the input or output
point.

229 m (750 ft) twisted wire

1.5 mm

2

(18 AWG) stranded

copper

B

137 m (450 ft) twisted wire

0.8 mm (20 AWG) stranded copper
297 m (975 ft) twisted wire

91 m (300 ft) twisted wire

0.6 mm (22 AWG) stranded copper
183 m (600 ft) twisted wire

61 m (200 ft) twisted wire

24 AWG stranded copper 107 m
(350 ft) twisted wire

N/A

See

Figure 4

to determine

cable length.

Use twisted wire cable.

See

Figure 4

to select wire

size/gauge.

Use stranded copper wire.

C

5

FX-PCV1656 Programmable VAV Box VAV Controllers Installation Instructions

Содержание FX-PCV1656














Отзывы: