Johnson Controls Frick QUANTUM LX Скачать руководство пользователя страница 111

Страница: 111 / 140

QUANTUM™ LX COMPRESSOR CONTROL PANEL

COMMUNICATIONS SETUP

090.020-CS (APRIL 13)

Page 111

COM-1 AND COM-2 DESCRIPTION

The board pictured on this page has two RS-422 seri-

al communications ports, labeled P10 (Com-1) and P11

(Com-2). They can be used for external communications

to the outside world.

COM-3 DESCRIPTION

Com-3 is labeled as P16 and is used for RS-422/RS-485

hardware protocol, and can be used in addition to any of

the other communications ports that may be being used.

COM-4 DESCRIPTION

Com-4 (RS-422/RS-485) is labeled as P17 and is dedicat-

ed to providing communications to the DIgital and Analog

boards, and will be explained in the section entitled

Com-

4 Description

ommunications Ports on the Q5 Interface Board

Q5 SERIAL COMMUNICATIONS HARDWARE

Q5 GENERAL DESCRIPTION

User connections for serial communications to and

from the Q5 are located on the Interface board, and

can use RS-422 and/or RS-485 hardware protocol.

These hardware protocols can be connected via

Com-3 and Com-4 for RS-485, and Com-1 and Com-

2 for RS-422/RS-485.

As mentioned in the previous paragraph, the user

connections for the serial communications portion

of the Q5 controller consists of an Interface board,

mounted below and to the right of the main con-

troller. In addition to external forms of serial com-

munication (to be discussed shortly), the keypad also

connects here:

COM-4

(RS-485)

COM-3

(RS-485)

COM-2

(RS-422/

RS-485)

Keypad

COM-1

(RS-422/

RS-485)

Содержание Frick QUANTUM LX













































































































































Результаты поиска

Содержание Frick QUANTUM LX

Отзывы:

Бренды по названию

Популярные бренды

Johnson Controls Frick QUANTUM LX, Настройка

Результаты поиска

Содержание Frick QUANTUM LX

Отзывы:

Бренды по названию

Популярные бренды