Johnson Controls Frick QUANTUM LX, Настройка

Страница: 11 / 140

QUANTUM™ LX COMPRESSOR CONTROL PANEL
COMMUNICATIONS SETUP
090.020-CS (APRIL 13)
Page 11
able to identify this particular compressor by (for example;
Unit1). The Host Name must be fi fteen characters or less
in length, use no spaces and use only upper and lower
case letters. It is similar in concept to the function of the
Panel ID, and basically allows the network router to in-
terpret the actual IP address of a particular unit as this
host name. When using a web browser within the system
network, this name can be entered as the web location
that you wish to visit (instead of having to type in the IP
address). After modifying a Host Name, you will be re-
quired to cycle power. The network router could take up
to fi fteen minutes to recognize the change.
Work Group – All of the Quantum™ LX units within a
network may be grouped into different categories. These
categories could be unit locations, or perhaps categorized
by unit function. For instance, if you wanted to group the
units by function, and had 10 units, and three of them
were Evaporators (located on the roof), then Evap1 could
be the name of a work group. Another three units may be
High Stage compressors, this work group could be named
HighStage1, and the remaining four units could be stan-
dard compressors, and they could be named Comp1. So
name each unit by these functional Work Group names.
The Work Group name must be fi fteen characters or less
in length, and can use numerals and upper and lower case
letters. When using the network neighborhood feature of
Windows® Explorer, by looking at your Network Neigh-
borhood, you would see the name of the Work Group,
and within that work group you would see the individual
Host Names of each unit within that work group. After
modifying a Work Group name, you will be required to
cycle power. The network router could take up to fi fteen
minutes to recognize the change.
Server String – This is a comment area that can be used
in conjunction with the Host Name. For example, if the
Host Name is Booster1, you could set the Server String
to print something like DockBooster, or some other ad-
ditional information about the unit. The Server String has
no control function; it is strictly an informational area.
E-MAIL DATA
The purpose of the E-Mail data feature is to allow the
controller to send a Warning or Shutdown message to
de fi ned listing of recipients.
Email Noti fi cation On Warning Or Shutdown – For the E-
mail noti fi cation feature to work, it must be enabled (it is
disabled as a default). The following drop-down menu is
provided:
• Disabled
• Enabled
Local Email Address - Use this setpoint box to enter a
valid E-mail address that has been assigned to the inter-
net account.
Alias Name For Local Email Address – Enter here a cus-
tom name to identify more clearly the local Email address.
When a message is sent to all recipients, this is the name
that will appear in the Email FROM column.
Subject - Enter a custom subject that you would like to
appear when a message failure is sent. When a message
is sent to all recipients, this is the wording that will appear
in the Email SUBJECT column.
SMTP Server Name OR IP Address - SMTP stands for
Simple Mail Transfer Protocol. SMTP servers handle out-
going email, and accept email from other domains. When
you set up an email client, you must specify an outgo-
ing server (sometimes called an SMTP server). Often, this
server is designated in the form of smtp.domain.com. But
this can vary, so be sure to check with your email service
provider or LAN administrator to fi nd out their outgoing
server.
SMTP Server Port Number - This value is in almost all
cases going to be 25. This should be set by the network or
LAN administrator.
Comma-Delimited List Of Email Recipients - This is
simply the list of the Email addresses that you would like
to have any messages sent to. Separate each e-mail ad-
dress with a comma.
PROTOCOLS
The purpose of this section is to enable or disable the
Modbus TCP and Ethernet/IP parameters.
Modbus TCP:
• Disabled
• Enabled
Ethernet/IP:
• Disabled
• Enabled