background image

536636-UIM-A-1209

SINGLE PIECE
VARIABLE SPEED AIR HANDLERS

MODELS: AV*(C) SERIES

INSTALLATION MANUAL

ISO 9001

Certified Quality

Management System

LIST OF SECTIONS

GENERAL  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
UNIT INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ELECTRIC HEATER INSTALLATION   . . . . . . . . . . . . . . . . . . . . . . . . 7
LOW VOLTAGE CONTROL CONNECTIONS   . . . . . . . . . . . . . . . . . .7

REQUIRED CONTROL SET-UP  . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
LINE POWER CONNECTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
AIRFLOW AND COMFORT SETTING SELECTION . . . . . . . . . . . .  13
UNIT DATA   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
MAINTENANCE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18

LIST OF FIGURES

Typical Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Return Duct Attachment & Component Location  . . . . . . . . . . . . . . . . . 3
Dimensions & Duct Connection Dimensions  . . . . . . . . . . . . . . . . . . . . 4
Condensate Deflector on Vertical Drain Pan  . . . . . . . . . . . . . . . . . . . . 5
Condensate Deflecctor on Horizontal Drain Pan Edge   . . . . . . . . . . . . 5
S-Clip Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Typical Horizontal Installation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TXV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
Proper Bulb Location   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
Air Handler Control Board – Communications Connections . . . . . . . .  8
Cooling Models with and without Electric Heat Wiring  . . . . . . . . . . . .  9
Two-Stage Heat Pump Wiring   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
Air Handler with Communicating AC or HP   . . . . . . . . . . . . . . . . . . .  10
Line Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12

LIST OF TABLES

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
Low Voltage Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
Low Voltage Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
Fault Codes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
Heat Relays   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
Comfort Setting Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
Physical and Electrical Data - Cooling Only (60 Hz)   . . . . . . . . . . . . . . . .  14
Electrical Data - Cooling Only (60 Hz)  . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
Conversion Table  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
Electrical Data - 208/230-1-60  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14

Electrical Data - (For Single Source Power Supply) - 
Copper Wire - 208/230-1-60  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Electrical Data - (For Multi-Source Power Supply) - 
Copper Wire - 208/230-1-60  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Electrical Data - 208/230-3-60   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Electrical Data - (For Single Source Power Supply) - 
Copper Wire - 208/230-3-60  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Electrical Data - (For Multi-Source Power Supply) - 
Copper Wire - 208/230-3-60  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Air Handler Air Flow Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

SECTION I: GENERAL

The AV single piece air handler provides the flexibility for installation in
any upflow, downflow, or horizontal application. 

These versatile models may be used for cooling or heat pump operation
with or without electric heat.

A BRAND LABEL (available from Distribution) may be applied to the
center of the blower access panel on AVG models.

The unit can be positioned for bottom return air in the upflow position,
top return air in the downflow position, and right or left return in the hor-
izontal position.

Top and side power wiring and control wiring, accessible screw termi-
nals for control wiring, easy to install drain connections and electric
heaters all combine to make the installation easy, and minimize installa-
tion cost.

SECTION II: SAFETY

This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.

Understand and pay particular attention to the signal words 

DANGER

,

WARNING

, or 

CAUTION

DANGER 

indicates an 

imminently

 hazardous situation, which, if not

avoided, 

will result in death or serious injury

.

WARNING 

indicates a 

potentially

 hazardous situation, which, if not

avoided, 

could result in death or serious injury

.

CAUTION 

indicates a potentially hazardous situation, which, if not

avoided 

may result in minor or moderate injury.

 It is also used to

alert against unsafe practices and hazards involving only property dam-
age.

Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service or mainte-
nance can cause injury or property damage. Refer to this manual
for assistance or for additional information, consult a qualified con-
tractor, installer or service agency.

This product must be installed in strict compliance with the installa-
tion instructions and any applicable local, state, and national codes
including, but not limited to building, electrical, and mechanical
codes.

Содержание AV Series





















Отзывы: