background image

 

SPECIFIC SAFETY RULES 

 
 
 

Do not

 drill material too small to be 

securely held. 
 

Always

 keep hands out of the path of the 

drill bit. Avoid awkward hand positions 
where a sudden slip could cause your hand 
to move into the path of the drill bit. 
 

Secure workpiece

. Use clamps or a vice 

to hold the workpiece. It is safer than using 
your hand and it frees both hands to 
operate the tool. 
 

Make sure

 there are no nails or foreign 

objects in the part of the workpiece to be 
drilled. 

 
To avoid injury

 from accidental starting, 

always remove the battery from the tool 
before installing or removing a drill bit. 
 

Do not

 install or use any drill bit that 

exceeds 7” (175 mm) in length or extends 
more than 6” (150 mm) beyond the chuck 
jaws. They can bend or break suddenly. 
 

Before starting

 the operation, jog the drill 

switch to make sure the drill bit does not 
wobble or vibrate. 
 

Do not use

 fly cutters or multiple-part hole 

cutters, as they can come apart or become 
unbalanced in use. 
 

Make sure

 the spindle has come to a 

complete stop before touching the chuck or 
attempting to change the drill bit. 
 

Always make sure the chuck is tight and 
the drill bit firmly tightened in the chuck 

before starting drill. 
 

 
 
 
 
 

Do not store or carry battery in a manner 
in which metal objects could contact the 
exposed metal end

. Do not place battery 

in aprons, pockets, drawers, etc. with loose 
nails, screws, keys etc. The battery could 
short circuit causing a fire, personal injury 
or damage to the battery. 
 

Never attempt to open the battery for 
any reason

. If the housing of the battery 

breaks or cracks, immediately  
discontinue use and do not recharge. 
 

Do not charge the battery if it is wet or 
shows any evidence of corrosion

 
A small leakage from the battery may occur 
under extreme usage, charging or 
temperature conditions. This does not 
indicate a failure. 

If however, the outer 

seal is broken and this leakage gets on 
your skin, follow these steps:

 

1.  Wash immediately with soap and 

water. 

2.  Neutralize with a mild acid such as 

lemon juice or vinegar. 

3.  If liquid gets into your eyes, flush 

immediately with clean water for a 
minimum of 10 minutes and seek 
medical attention. 

NOTE:

 The battery liquid is a 20

–35% 

solution of potassium hydroxide. 
 

Do not incinerate the battery

. It can 

explode in a fire. 
 

Do not use an extension cord

. Plug the 

charger cord directly into an electrical 
outlet. 

BATTERY & CHARGER 

SAFETY 

Содержание 54-2891-8























Отзывы: