background image

 

18 

 
 
 
GENERAL 

 

        

WARNING:

 When servicing, use 

only identical JobMate

™ replacement 

parts. Use of any other part may create a 
hazard or cause product damage. 

 
DO NOT use solvents when cleaning 
plastic parts. Most plastics are susceptible 
to damage from various types of 
commercial solvents and may be damaged 
by their use. Use clean cloth to remove dirt, 
dust, oil, grease etc. 
 

        

WARNING:

 Do not at any time 

allow brake fluids, gasoline, petroleum-
based products, penetrating oils, etc. to 
come in contact with plastic parts. They 
contain chemicals that can damage, 
weaken or destroy plastic. 

 
DO NOT abuse power tools. Abusive 
practices can damage the tool as well as 
the workpiece. 
 

        

WARNING:

 DO NOT attempt to 

modify tools or create accessories not 
recommended. Any such alteration or 
modification is misuse and could result 
in a hazardous condition leading to 
possible serious injury. It will also void 
the warranty. 

 

LUBRICATION 

 
All of the bearings in this tool are lubricated 
with a sufficient amount of high-grade 
lubricant for the life of the unit under normal 
conditions. Therefore, no further lubrication 
is required. 

 
 
 

BATTERY PACK REMOVAL AND 
PREPARATION FOR RECYCLING 

 
To preserve our natural resources, please 
recycle or dispose of batteries properly. 
 
This product contains nickel-cadmium 
batteries. Never dispose of nickel-cadmium 
batteries in your normal household garbage 
or in landfill sites as they will add to the 
pollution of the environment. 
 
Consult your local waste authority for 
information regarding available recycling 
and disposal options. 

 
        WARNING:

 

Upon removal of the 

battery pack, cover the terminals of the 
battery pack with electrical or heavy-
duty adhesive tape.

 

Never touch both 

terminals with metal objects or body 
parts as a short circuit may result. Keep 
away from children. Do not attempt to 
destroy or disassemble battery pack or 
remove any of its components. Nickel-
cadmium batteries must be recycled or 
disposed of properly. Failure to comply 
with these warnings could result in fire 
and serious injury

.

MAINTENANCE 

 

 

Содержание 54-2891-8























Отзывы: